Bluetooth RF Test Matrix
For more information refer to Bluetooth Test
|Meets fully specified Bluetooth® certification test requirements|
|Bluetooth certification pre-compliance testing only|
|Meets fully specified Bluetooth certification test requirements when combined with other equipment|
|Structured test cases for certification testing of the Bluetooth RF layer (defined by Bluetooth SIG)||N4010A Wireless Connectivity Test Set||ESA-E Series Spectrum Analyzers||X-Series Signal Analyzers with N9081A and W9081A measurement application||N5182A MXG and E4438C ESG Vector Signal Generators with N7606B Signal Studio software||P-Series, EPM-P Series Power Meters||89600B VSA Software||E8257D PSG Analog Signal Generator|
|Output power [TRM/CA/01/C]|
|Power density [TRM/CA/02/C]||7|
|Power control [TRM/CA/03/C]||8||7, 8|
|Tx output spectrum frequency range [TRM/CA/04/C]||7|
|Tx output spectrum -20 dB bandwidth [TRM/CA/05/C]|
|Tx output spectrum adjacent channel power [TRM/CA/06/C]|
|Modulation characteristics [TRM/CA/07/C]|
|Carrier frequency drift [TRM/CA/09/C]||6|
|EDR Relative Transmit Power [TRM/CA/10/C]|
|EDR Carrier Frequency Stability and Modulation Accuracy [TRM/CA/11/C]|
|EDR Differential Phase Encoding [TRM/CA/12/C]|
|Sensitivity/single-slot packets [RCV/CA/01/C]|
|Sensitivity/multi-slot packets [RCV/CA/02/C]|
|C/I performance [RCV/CA/03/C]||1||1|
|Blocking performance [RCV/CA/04/C]||2||2||2|
|Intermodulation performance [RCV/CA/05/C]||3||3||3|
|Maximum input level [RCV/CA/06/C]|
|EDR Sensitivity [RCV/CA/07/C]|
|EDR BER Floor Performance [RCV/CA/08/C]|
|EDR C/I Performance [RCV/CA/09/C]||5|
|EDR Maximum Input Level [RCV/CA/10/C]|
|Low Energy (LE) or Ultra Low Power (ULP)|
|Output power [TRM/CA/01/C]|
|In-band emission [TRM/CA/02/C]|
|Modulation characteristics [TRM/CA/03/C]|
|Carrier frequency offset and drift [TRM/CA/04/C]|
2 The blocking performance receiver test requires a Bluetooth modulated source such as the N4010A, N5182A MXG or E4438C ESG and a microwave signal source such as the N5183A MXG Analog Signal Generator or E8257D PSG to generate the interfering signal (30 MHz to 12.75 GHz).
3 The intermodulation performance receiver test requires two Bluetooth modulated sources such as the N4010A, N5182A MXG, or E4438C ESG and one CW/analog source such as the MXG N5181A, N5183A MXG, E4428C ESG or the E8257D PSG to generate intermodulation.
4 N4010A-101 for Bluetooth required for Bluetooth 1.2 tests. Option 101 and Option 107 required for Bluetooth EDR tests.
5 The EDR C/I performance receiver test requires an additional signal source with Bluetooth EDR capability such as the N4010A EDR Tx/Rx Option 105 or N5182A MXG signal generator with N7606B Signal Studio software.
6 Requires Option AYA
7 Requires use of GPSA mode
8 Power control test could be accomplished by manual output power test step by step if the DUT can be controlled in this manner.
Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc., U.S.A. and licensed to Agilent Technologies, Inc.
Enroll in myAgilent
A personalized view into the information most relevant to you.
Register Your Product
Register your products for service notifications, firmware update alerts, application notes and more…
Why Buy Agilent
See how the Agilent Advantage adds value to your purchase.
Learn about Keysight
Agilent’s Electronic Measurement Group is becoming Keysight Technologies.