Aerospace and Defense Applications – Video Series
Focus where it counts 
Achieve your program or mission goals by staying on top of the latest test technologies in Radar/EW, MilComms, Satellite and ELINT/SIGINT. Tune into these short application videos for the latest on RF, uW and mmW measurements, signal generation, distortion and modulation for wideband comms, OFDM waveforms, phase noise and more. By helping you anticipate and build greater assurance in system readiness, Agilent frees you to focus where it counts most.
Download the videos by clicking on the links below.
|
Multi-Emitter Signal Scenarios The video shows an approach used to create multi-emitter signal scenarios with commercial off-the-shelf design software and instrumentation for a cost-effective test solution for present and future multi-emitter R & D applications. |
YouTube Video 2013-02-01 |
MP4 55 MB
|
|
How to Accelerate Large-Scale Antenna Calibration & Testing with High-Speed Digitizer Learn about Agilent‘s digitizer based solution which helps accelerate multi antenna calibration or channel sounding significantly. It is based on the M9703A 8-channel, 12-bit high-speed digitizer with exclusive digital downconverter capabilities. |
YouTube Video 2013-02-01 |
MP4 26 MB 2013-02-01 |
|
Interference Mitigation Through the Use of Wideband Signal Recording and Analysis This video describes the process to find and analyze the cause of a radio signal that is interfering with a wireless LAN transmitter. This requires the continuous capture of wireless spectrum, tools to search and find possible interferers as well as tools to determine how an interferer may affect the LAN signal... |
YouTube Video |
WMV 34 MB |
|
Microwave Switch Repeatability Demonstration |
YouTube Video |
WMV 19.4 MB |
|
Using Command Expert to Control Instruments in Excel This video introduces Command Expert running as an Excel ad-in. It highlights the capabilities to assist in instrument programming and shows how an instrument programming sequence can be integrated with Excel in order to set system parameters and display the results of measurements. |
YouTube Video |
WMV 66.6 MB |
|
OFDMA Concepts Demonstration - channel training sequence This video describes one of the key concepts of Orthogonal Frequency Division Multiple Access (OFDMA) modulation. This video illustrates how a channel training sequence can be used to discern two distinct transmission streams in a MIMO (Multiple In Multiple Out) Antenna configuration. |
YouTube Video |
WMV 20.5 MB |
|
Reproducing DC Power Transients, Using an N6705B DC Power Analyzer to Create Transients DC power transients can easily be reproduced with N6705B DC Power Analyzer. Power transients can be used to test a DUT resilience to a change in voltage. Two examples are provided an automobile's voltage during engine turn-on and a PS interrupt specified in the DO-160F avionics test manual. Transients can also occur when the load on a PS changes. |
YouTube Video |
WMV 20.5 MB
|
|
Reconfigurable Radar Design: Debug and Validation This video demonstrates how to debug and validate reconfigurable radar design with Agilent test and measurement instruments and software. |
YouTube Video |
WMV 104 MB |
|
EVM Measurement with the New M8190A Arbitrary Waveform Generator To meet the high demands of aerospace/ defense application tests, it is indispensable to simulate real-life scenarios with precision arbitrary waveforms. In a test setup with a high error vector magnitude (EVM), problems within your device under test may not be discovered. With signals close to reality, the Agilent M8190A is the perfect solution. |
YouTube Video |
WMV 40 MB |
|
Best IF Signal Quality using Digital Up-conversion with the Agilent M8190A Arbitrary Waveform Generator Digital up-conversion takes testing one step further. The wide bandwidth of the M8190A allows generating the IF signal directly. The IQ data will be up-converted digitally in hardware which gives you best signal quality in the desired frequency range. |
YouTube Video
|
WMV 121 MB |
|
Generation and Analysis Techniques for Cost-efficient SATCOM Measurements Watch this new video from Agilent’s presentation at the 2012 IEEE International Microwave Symposium, which provides information on making SATCOM-type wideband measurements that are generally higher in frequency, typically around Ka-Band. One of the topics covered is correction techniques that enable lower cost of test. |
YouTube Video |
MOV 995 MB |
|
When Does Phase Noise Matter? Sometimes phase noise matters and sometimes it doesn’t. Watch this new video to better understand phase noise needs and tradeoffs. Included in the video is a radar example, where phase noise matters, and an OFDM example, where it’s not as important, as well as how to improve phase noise and signal generation while balancing performance with cost. |
YouTube Video |
MOV 13 MB |
|
Easy Radar Emulation for Radar & EW Test See how radar emulation can be achieved with carriers from 0-44 GHz for radar and electronic warfare testing. In this video, an Agilent arbitrary waveform generator and signal source are programmed to emulate an ASR-11 airport surveillance pulse pattern, which is then analyzed using a signal analyzer running a pulse analysis application. |
YouTube Video |
MP4 40 MB |
|
Measure Wideband Radar Signals Watch this new video to see a demonstration of how to perform measurement of wideband radar signals. The video shows how to correct the amplitude flatness of the IF, producing flat IF frequency and response across the whole bandwidth with Agilent’s cost-effective wideband analysis solution for measuring radar and satellite signals. |
YouTube Video |
MP4 55 MB |
|
Discover the Smarter Solution to your mmWave Applications This video demonstrates how smart mixers extend the operating frequencies of the N9030A PXA signal analyzers up to 110 GHz for millimeter-wave applications. |
YouTube Video |
MP4 73 MB |
Enroll in myAgilent
Register Your Product
Why Buy Agilent