Contact an Expert

Technical Support

Test & Measurement

Find by Product Model Number: Examples: 34401A, E4440A

Refine the List

remove all refinements

By Topic

By Type of Content

By Product Category

1-25 of 40

Sort:
How can I transfer a "state" from one PSG to another?
Using ftp, the transferred states are not visible in the Recall list.

FAQ 2012-06-07

How do I get the N5182A/N5162A MXG default waveform files from Agilent and download them into the N5182A/N5162A MXG memory?
The arbitrary waveform files are stored in the non-volatile memory of the N5182A/N5162A MXG when they ship out of the factory. In case these waveform files are accidentally deleted, a user can retrieve them through either of the following methods...

FAQ 2012-06-07

How do I get started with programming the ESG or PSG using Intuilink and Agilent VEEPro?
The attached program illustrates the basic connectivity with the ESG/PSG using the Intuilink driver.

FAQ 2012-05-30

Can we upgrade N5181A or N5182A first-generation MXG to an N5181B or N5181B MXG X-Series signal generator?
No, there is not a hardware upgrade path from the first-generation MXG to MXG X-Series signal generator.

FAQ 2012-04-30

How do you change the programming language expected by the the 6030A, 6031A, 6032A, 6033A, 6035A, or 6038A power supplies?
These products are shipped from the factory in their native language (called Compatible Language Mode) with their hardware address set to "Adr 5". The programming language can only be changed to SCPI Mode via a controller by sending the string "SY...

FAQ 2010-09-09

What are the file formats used for the MXG?

FAQ 2010-09-08

IO Libraries Suite: Where do I find sample programs for SICL, VISA, and VISA COM?
Sample programs are available using SICL, VISA, and VISA COM in the IO Libraries Suite installation and on Agilent.com

FAQ 2010-09-08

How can you change or view the secondary address in the 6030A, 6031A, 6032A, 6033A, 6035A, or 6038A power supplies?
These products have been retrofitted with SCPI language capability, in addition to the original or compatibility mode. Secondary addressing of these products is only available in SCPI mode.

FAQ 2010-09-08

66000A: Setting Dwell Time
The List mode can contain up to 20 Voltage, Current or Dwell steps if controlled over the GPIB, or up to 8 steps if controlled from the optional keyboard...

FAQ 2010-05-26

IO Libraries Suite: What programming languages are supported with Agilent IO Libraries version 15.1?
It depends on the API you are using.

FAQ 2009-08-25

IO Libraries Suite: Is there any other software that needs to be installed when I am using an application that utilizes NI-488.2 and Agilent IO Lib...
It depends if there is third party connectivity hardware or software installed.

FAQ 2009-08-25

Which of the E36xxA power supplies can be controlled from the remote interface?
The Agilent E3631A, E3632A, E3633A, E3634A, E3640A, E3641A, E3642A, E3643A, E3644A, E3645A, E3646A, E3647A, E3648A, and E3649A power supplies are fully programmable and you can program them from the RS-232 or GPIB (IEEE-488) interface. Both remote...

FAQ 2008-09-23

Does the Agilent E364xA offer any alternative programming languages?
The Agilent E364xA's programming language is compatible with SCPI (1998) and IEEE 488.2. No other programming languages are available.

FAQ 2008-09-22

66xxA and E36xxA: Programmable Current Sinking
In general, current sinking is a fixed value at some percentage of the full scale current output. However, there is an exception for one series of Agilent power supplies. On the 663xB series, the maximum negative current tracks the value programme...

FAQ 2008-09-22

E363xA and E364xA: Compatibility with National GPIB I/F Card
Yes, the National Instruments GPIB board is very configurable. However, this can cause some problems.

FAQ 2008-09-22

Can you download the values of the X and Y axis of a waveform obtained from the oscilloscope into a function generator to be use as the output?
Yes.

FAQ 2008-08-29

Can I program a waveform captured by my oscilloscope into an Agilent arbitrary waveform generator?
Yes. The free IntuiLink Waveform Editor software will download waveform data from Agilent Infiniium, 6000 series, and 54600 series oscilloscopes and send the data to the an Agilent 33120A, 33210A, 33220A, or 33250A generator.

FAQ 2008-08-29

Why doesn't my System Power Supply accept commands over the GPIB?
If you are getting either error 11 or error 113 when you try to send GPIB commands to your system supply, it may be that you are using the wrong command language.

FAQ 2008-07-29

FAQs: Waveform Downloads and Storage

FAQ 2008-01-18

ESG and ESG-D Series: Backwards Compatibility with 8657D Signal Generator

FAQ 2005-05-25

What are the ESG query commands?

FAQ 2005-05-23

Why doesn't the ESG display update when I am running a program in the remote mode?

FAQ 2005-05-23

ESG Series: Dual ARB, Option UND

FAQ 2003-03-14

Why do I get syntax and undefined header errors when using LabView and the 33120A?
The first place to look is at the commands you are sending to the instrument from LabView.

FAQ 2002-11-26

Where is the cfunc.h header file called for in the 33120A Users Guide example program?
Some older versions of the IB Libraries provided this header file during installation. This file was required to access commands from the IB command library.

FAQ 2002-11-26

1 2 Next