Technical Support

Test e Misura

By Type of Content

FAQ (374)

By Product Category

All Product Categories
- Additional Test & Measurement Products
  - Photonic Test & Measurement Products
    - Optical Component Test Products (9)
    - Digital Modulation, Time & Error Measurements (132)

1-25 of 374

Infiniium 90000 and 9000 Series Oscilloscope Software Infiniium 90000 and 9000 Series oscilloscope software. FAQ 2013-05-15
Do you have an example C# code to control the N4960A BERT? Yes. FAQ 2013-05-06
How can I bundle N1045A remote heads together in a tight space? For simple differential setups, two heads can simply be clipped together using the supplied clip. To mount more heads see the full body of this FAQ for mounting dimensions and thermal considerations. FAQ 2013-04-24
8614xA/B Optical Spectrum Analyzer Firmware Firmware revisions are made to add enhancements and to fix defects. We recommend that you use the latest version of firmware available. FAQ 2013-03-20
UNH-IOL JBISTGUI Software JBISTGUI utilizes the two channel mode of J-BERT N4903B and configures transmission of the necessary pattern sequences that can enable the BIST-L and BIST-TAS test modes for SATA host and device products. This Software simplifies Agilent’s receiver test setup by eliminating the need to switch between a protocol tester and J-BERT. FAQ 2013-03-18
How do I measure Bit Error Rate (BER) to a given confidence level on N490xA/B Serial BERTs? FAQ 2012-12-12
What are the rack mount kit part numbers for the 86100 DCA? Rack mount kits for 86100 DCA are available to purchase as stand-alone parts. FAQ 2012-11-13
Which Agilent oscilloscopes have a 10 MHz reference input/output? 6000 Series, 6000L Series, 7000A Series, 7000B Series, 9000 Series, 54850 Series (Output only), 80000A Series, 80000B Series, 90000A Series and 90000 X-Series FAQ 2012-09-29
All IntuiLink Tools for Agilent Oscilloscopes Supported Models: Infiniium Series, 1000 Series, 2000 X-Series, 3000 X-Series, 5000 Series, 6000 Series, 7000 Series, and 54600 Series Oscilloscopes FAQ 2012-09-26
How can I de-embed a test fixture using the 86100C/D Digital Communications Analyzer? N1010A software with InfiniiSIM-DCA option provides the capability to de-embed and embed fixtures, cables, probes, and other circuit elements. FAQ 2012-08-06
What is the typical power consumption of the 86100C and 86100D Digital Communications Analyzer? Typical measurements of 86100C and 86100D power consumption FAQ 2012-08-06
Which probe positioners are available to hold the N1021B? The adapter provided with the N1021B is generic enough to work with robot arms or common industry positioners ... FAQ 2012-07-06
Why do the high-bandwidth 54850-series Infiniium scopes use a BNC connector? The 54850-series Infiniium scopes use a "precision BNC" connector. FAQ 2012-04-09
How do I establish a peer-to-peer connection between my PC and an InfiniiVision 5000/6000/7000 Series oscilloscope? There are two methods ... FAQ 2012-03-27
How much the default RF port power of N4375B? And can I change it? It is 0 dBm, and you can change it. FAQ 2012-03-01	PDF 46 KB
What is difference between connector option 021, 022 and 023 in 8167 series and 8168 series tunable laser source (8167A/B, 8168A/B/C/D/E/F)? FAQ 2012-02-17
ValiFrame MHL Download ValiFrame software from BitifEye support page... FAQ 2012-01-11
Can the 816x mainframes be controlled via GPIB? Yes, the 816x mainframes offer complete GPIB control using either SCPI commands or the VXI PNP drivers. FAQ 2011-12-09
Where can I find manuals for discontinued and obsolete Hewlett-Packard and Agilent test equipment? Most Agilent products have PDF manuals that can be found on product pages. Other vendors also supply old manuals. FAQ 2011-07-13
Does Agilent offer an LC adapter for modules? Agilent Technologies offers different ways to connect an LC connector to our optical instrumentation. FAQ 2011-07-08
How do I upgrade the firmware for large slot tunable lasers in the 8164 mainframe? You can upgrade the 816xx full size tunable lasers firmware via GPIB, via floppy disks or ... FAQ 2011-07-06
Can I use the 81000FB bare fiber adapter with laser sources? No, the 81000FB is designed for adapting bare fibers to sensor modules only. FAQ 2011-07-06
How can I reset the password to the factory setting '1234'? The password, as well as all other user settings, can be reset to the factory default settings by ... FAQ 2011-07-06
What is the calibration cycle for the 8163x / 8153x power sensor modules? The calibration cycle for the newer optical sensors (8163x) is 24 months. FAQ 2011-07-06
What accessories should I order with my 8156A? The 8156A has either two or three fiber connections consisting of an input, output, and monitor output. FAQ 2011-07-06

1 2 3 4 5 6 7 8 9 10 ... Next

Technical Support

Test e Misura

Refine the List

By Topic

By Application

By Type of Content

By Product Category

1-25 of 374

Prodotti e Servizi

Supporto tecnico

Applicazioni & Soluzioni

Informazioni su Agilent