|
|
|
8753A Network Analyzer Upgrade
|
2005-04-18
|
FAQ
|
|
|
|
|
Agilent 8903A, SINAD Measurement and Board Upgrades
There are potentially 4 changes required depending on the serial prefix of the 8903A...read more
|
2006-02-03
|
FAQ
|
|
|
|
|
Are replaceable parts available to a 4193A component adapter (04193-61153)?
Yes, the replaceable parts are P/N:1250-0928 for the female contact inside the component adapter and P/N:04193-60151 for the terminals of the component side of the adapter.
|
2008-06-27
|
FAQ
|
|
|
|
|
Are the Agilent 4338A and 4338B milliohmmeters code compatible?
Most programming commands for the Agilent 4338B are compatible with 4338A, except...
|
2008-07-07
|
FAQ
|
|
|
|
|
Can I control the E5515C over the LAN?
No, control of the E5515C is available through GPIB only.
|
2006-02-06
|
FAQ
|
|
|
|
|
Can I download the drivers for the Agilent GPIB interfaces?
Yes, you may download them from the web
|
2006-07-11
|
FAQ
|
|
|
|
|
Can I save the display screen on the Agilent 4291B, 4395A, and 4396B Analyzers as a color TIFF(Tagged Image File Format) file?
Yes, the display screen on the Agilent 4291B, 4395A and 4396B can be saved as TIFF formatted image files.
|
2005-12-23
|
FAQ
|
|
|
|
|
Can I transfer 34401A or 34420A measured data to my PC without any programming?
You can transer the data using IntuiLink Multimeter software or the RS-232 Port.
|
2005-05-06
|
FAQ
|
|
|
|
|
Can I upgrade an earlier version of the 4062 to a 4062UX?
It depends upon the precise configuration of your system...
|
2006-01-17
|
FAQ
|
|
|
|
|
Can I use 11970 or 11974 series external mixers with my Agilent 859x series Spectrum Analyzer?
No, while the 859X products did offer an L.O. output on the rear panel with option 010, Tracking Generator, there was never a provision for an I.F. Input, which is required for external mixing. Therefore external mixing cannot be performed using an 859x product.
|
2008-11-10
|
FAQ
|
|
|
|
|
Can I use the 5475xA modules and the TDR capability of the 54753A/4A modules in 83480A mainframe?
Yes, if the 54755A firmware option is installed.
|
2006-07-13
|
FAQ
|
|
|
|
|
Can I use the 6811B, 6812B, or 6813B Power Meter and Analyzer on external AC power lines?
No. It can only be used to test devices.
|
2006-06-20
|
FAQ
|
|
|
|
|
Can I use the 8348xA/B modules in the 54750A mainframe?
Yes. You can use 8348xA/B modules in the 54750A mainframe if you install the 83480K firmware...
|
2005-05-03
|
FAQ
|
|
|
|
|
Can I use the Agilent 6811A, 6812A, and 6813A Power Source in place of the 6811B, 6812B, and 6813B, respectively?
Yes, as long as the Harmonic Flicker software is not used.
|
2006-03-06
|
FAQ
|
|
|
|
|
Can you advise of alternatives to printing and acquiring screen images from the various Agilent Analyzers equipped with only a GP-IB interface?
|
2009-03-17
|
FAQ
|
|
|
|
|
For the InfiniiMax probes, what effect does the "Signal being probed" setting have? Why do I have to specify single-ended or differential?
Infiniium scopes and InfiniiMax differential probe amplifiers have a unique method of applying DC offset which considers whether the signal being probed is single-ended or differential...
|
2006-12-04
|
FAQ
|
|
|
|
|
How can I accomplish the adjustments and performance tests using other PI test fixtures like 41901A or 41902A than the 41900A?
Before starting the calibration, you should set the appropriate calibration standard values for the 41901A or 41902A, which refers to E4915A/16A User's guide page 5-12.
|
2008-06-27
|
FAQ
|
|
|
|
|
How can I clear the memory on an 8566B, 8567A, or 8568B Spectrum Analyzer for security reasons?
See content for details on this subject....
|
2005-08-03
|
FAQ
|
|
|
|
|
How can I determine the firmware revision for the 8153A mainframe?
You can determine the firmware for the 8153A mainframe by performing the following steps.
|
2006-06-27
|
FAQ
|
|
|
|
|
How can I order supplemental parts for component test fixtures/accessories?
You can order the necessary parts by the part numbers shown in the Accessories Selection Guide for Impedance Measurements.
|
2008-04-22
|
FAQ
|
|
|
|
|
How can I transfer acquired data or screen shots from my 1660/1670 series logic analyzer to my PC?
There are several ways to accomplish this. Here we’ll cover the popular method of printing to a file and then transferring that file to a PC via FTP.
|
2005-09-21
|
FAQ
|
|
|
|
|
How do I declassify or sanitize my 1660A-series logic analyzer?
This involves following a procedure that clears all user data from the instrument's memory.
|
2006-10-05
|
FAQ
|
|
|
|
|
How do I get Instrument Drivers for Agilent Test & Measurement Products?
From the CD shipped with the instrument or from the product technical support web page for the instrument.
|
2009-05-01
|
FAQ
|
|
|
|
|
How do I order 2.4mm connector gages?
2.4mm connector male and female gages are ordered separately...
|
2007-02-27
|
FAQ
|
|
|
|
|
How do I order 3.5 mm connector gauges?
|
2009-03-17
|
FAQ
|
|
