Parla con un Esperto

Technical Support

Test e Misura

Find by Product Model Number: Examples: 34401A, E4440A

151-175 of 803

Sort:
Where can I upgrade my existing U8903A to digital audio option?
The retrofit upgrade is available in Agilent service support center.

FAQ 2012-07-25

Can user create custom digital audio filters for U8903A?
Yes, users can create custom digital audio filters with Matlab and upload them to U8903A through the USB port.

FAQ 2012-07-25

What is preventing the 89600A software running on a PC from connecting to an X-Series analyzer?
These requirements MUST be observed when using the 89600A VSA software with an X-Series Signal Analyzer.

FAQ 2012-06-12

Can we switch the RRC filter on or off in modulation analysis measurements like Code Domain, Mod Accuracy, and QPSK EVM in the Agilent PSA and Agil...
Yes, please check the measurement setup menus when Code Domain, Mod Accuracy, or QPSK EVM is selected.

FAQ 2012-05-30

How does the “DPCH/E-DPCH Config” menu under Meas Setup in W-CDMA Code Domain effect on the measurement results for the Agilent PSA Series Spectrum...
This menu is added for HSUPA uplink code domain analysis. It helps identifying the code channel type among the detected active code channels. Based on the selected configuration with “DPCH/E-DPCH Config” the code power beta calculation should be c...

FAQ 2012-05-30

Can I measure Power vs. Time of the 1xEV-DO forward link signals with idle slot and active slot mixed condition for the Agilent PSA Series Spectrum...
Yes. PSA firmware A.09.18 and later and E4406A VSA firmware revision A.10.06 and later have measurement setup menu for such mixed and burst signals. When Idle Slot is selected in {Slot Type} under [Meas Setup] menu in Power vs. Time, active slots ...

FAQ 2012-05-30

Can I measure Modulation Accuracy of the 1xEV-DO forward link signals with idle slot and active slot mixed condition for the Agilent PSA Series Spe...
Yes. PSA firmware A.09.18 and later and E4406A VSA firmware revision A.10.06 and later have more robustness for such mixed and burst signals.

FAQ 2012-05-30

Can I measure Rho Overall in Modulation Accuracy of the 1xEV-DO forward link signals, because it was available in my PSA and/or E4406A VSA with old...
Yes. Please check the measurement setup menu to add Rho Overall result in Modulation Accuracy.

FAQ 2012-05-30

Can I measure 1xEV-DO signals in a single carrier or multi-carrier conditions? There was a carrier selection menu under Mode Setup in previous PSA ...
We have changed the measurement setting in Code Domain and Modulation Accuracy with the latest firmware of PSA and E4406A VSA.

FAQ 2012-05-30

Can we select a specific view to zoom in for GSM and EDGE measurements of Agilent PSA series spectrum analyzer?
Following measurements have new remote control SCPI commands with PSA firmware revision A.09.18 or later; GMSK Power vs. Time, GMSK ORFS, GMSK PFER, EDGE Power vs. Time, EDGE ORFS and EDGE EVM.

FAQ 2012-05-30

Can I use phase and frequency compensation setup for 1xEV-DO signal analysis in Code Domain Power for the PSA and E4406A 1xEV-DO personality?
We have changed the measurement setting in Code Domain with the latest firmware of PSA and E4406A VSA. Previously, there were phase and frequency compensation menus under [Mease Setup] > {Advanced} in PSA and E4406A VSA firmware, and they worked t...

FAQ 2012-05-30

Can we turn off the limit lines in Spectrum Emission Mask measurement for the PSA and E4406A W-CDMA, cdma2000, and 1xEV-DO personalities?
The Agilent PSA series firmware revision A.09.18 or later and the Agilent E4406A firmware revision A.10.06 or later have the remote control SCPI commands for this purpose.

FAQ 2012-05-30

Can we get the measured results of 1xEV-DO Modulation Accuracy in relative linear (no unit), not in relative power (dB) for the PSA and E4406A 1xEV...
3GPP2 C.S0032-A and C.S0033-A Minimum Performance Specifications describes required value as 0.0021 in Forward Link Max MAC inactive channel power fail limit for subtype0/1. It’s useful to get the results without converting from dB to linear value...

FAQ 2012-05-30

For the PSA Series Spectrum Analyzers, is the new two year calibration cycle applicable to all instruments?
Based on evaluation of serviced PSAs, Agilent determined that the PSA is stable enough to support a 2 year calibration cycle for all PSA instruments.

FAQ 2012-05-30

There are many view selections in 1xEV-DO Modulation Accuracy Personality for PSA and E4406A. Based on the conformance tests defined in 3GPP2 C.S00...
Please refer the measurement results in “Summary Peak/Avg Metrics” view by selecting under PSA [View/Trace] button.

FAQ 2012-05-30

What is the maximum DC input for PSA Series Spectrum Analyzer?
AC/DC coupling values found here...

FAQ 2012-05-30

For the PSA Series spectrum analyzer, is gated sweep capability required for options 212 (TD-SCDMA Modualtion Analysis) and 213 (HSDPA / 8PSK for T...
No, Gated sweep is not required.

FAQ 2012-05-30

For my PSA Series Spectrum Analyzer, what is recommended to do if my instrument is having trouble saving files or the instrument firmware is unexpe...
This issue may be caused by a corrupt firmware file or may be caused by a defect in firmware. Please first try upgrading the instrument’s firmware to the latest version posted on the Agilent web. This issue may also be caused by a hardware probl...

FAQ 2012-05-30

For the PSA Series spectrum analyzer, do I need to have option 212 (TD-SCDMA Modualtion Analysis) installed before I can install option 213(HSDPA /...
Yes, option 213 requires option 212 to be installed and licensed before it can be used.

FAQ 2012-05-30

For the PSA Series spectrum analyzer Is option B7J (digital demod hardware) required to use option 212 (TD-SCDMA Modualtion Analysis) or 213 (HSDPA...
Yes, when using option 212 or 213, option B7J is required.

FAQ 2012-05-30

Does the E7495A/B Wireless Base Station Test Set support frequency-panning in Spectrum Analyzer mode?
Yes, this feature was added in firmware version A.02.10. Click here for information on frequency-panning.

FAQ 2012-05-29

Are there any known issues when downgrading the VSA firmware?
When downgrading firmware on the E4406A there is an issue with the firmware upgrade program. You must first completely uninstall any previous installation of the upgrade program before installing an older version.

FAQ 2012-05-29

Can the E4406A or PSA Series cdmaOne personality (Option BAC) make power timing and phase measurements?
Yes. In the cdmaOne personality you will first need to change the Measure Method to Timing and Phase under the Measure Setup key and then change the view to Power Timing and Phase under the View/Trace key.

FAQ 2012-05-29

Why is the AC to DC power supply for my E7495A/B Base Station Test Set not working?
Click here for information about the AC to DC power supply for E7495A/B.

FAQ 2012-05-29

How do I remotely make an Adjacent Channel Power (ACP) measurement with the 89601A VSA software using Microsoft Excel?
Click here for information on controlling the 89601A software using Excel to make an ACP measurement.

FAQ 2012-05-29

Previous 1 2 3 4 5 6 7 8 9 10 ... Next