Contact an Expert

Technical Support

Test & Measurement

Find by Product Model Number: Examples: 34401A, E4440A

51-75 of 134

Sort:
How can I eliminate the flashing single digit in the front-panel display?
The flashing digit indicates the digit of the output parameter displayed that can be changed by turning the front panel knob. Use the resolution key (<) or (>) to move the flashing digit to the left or right until the flashing stops.

FAQ 2010-09-08

What is the settling time for the E364xA supplies?
For the E364xA series, Settling Time is defined as the maximum time required for the output voltage to change from 1% to 99% (or vice versa) following receipt of a VOLTage or APPLy command from the GPIB or RS-232 interface. The settling time is <...

FAQ 2010-09-08

E363xA and E364xA: Disabling the Control Knob
To disable the front-panel control knob, scroll the flashing digit on the front-panel display to the right or left using the selection keys (<) or (>) until the flashing digit disappears. Notice that the control knob and all front-panel keys are n...

FAQ 2010-09-08

How can you change or view the secondary address in the 6030A, 6031A, 6032A, 6033A, 6035A, or 6038A power supplies?
These products have been retrofitted with SCPI language capability, in addition to the original or compatibility mode. Secondary addressing of these products is only available in SCPI mode.

FAQ 2010-09-08

66xxA and E36xxA: Determining Power Supply Constant Current Mode
The power supply cannot be "put" into the constant current mode.

FAQ 2010-08-27

For the E363xA and E364xA Bench Power Supply, the display update speed when the "Display Limit" function is on is different from …
For the E363xA and E364xA Bench Power Supply (BPS), the display update speed is different because....

FAQ 2010-08-09

How can I prevent a loading delay when using the Agilent Measurement Manager with Microsoft® .NET 2.0 on a computer that is connected to a LAN…
To prevent a loading delay when using the Agilent Measurement Manager (AMM) with Microsoft® .NET 2.0, follow the instructions below:….

FAQ 2010-08-09

What are the differences between the Agilent N6705A DC Power Analyzer and the N6705B DC Power Analyzer?
The N6705B mainframe has new labeling that identifies which knobs have secondary functions when you press them...

FAQ 2010-08-09

When will Agilent USB modular instruments and USB Modular DAQs supports Windows 7?
For 32 bit Windows 7, the supportability of modular instruments and DAQs will happen...

FAQ 2010-07-18

66000A: Setting Dwell Time
The List mode can contain up to 20 Voltage, Current or Dwell steps if controlled over the GPIB, or up to 8 steps if controlled from the optional keyboard...

FAQ 2010-05-26

Why USB modular instruments (U272XA, U2741A, U2751A and U2761A) is not detectable by E5813A?
PC is failed to enumerate the USB modular instrument.

FAQ 2010-04-09

Is U2723A compatible with E5813A?
No

FAQ 2010-03-22

Is U2722A compatible with E5813A?
No

FAQ 2010-03-22

Are there other resources for my DC power supply product questions?
Agilent's discussion forums at https://forums.tm.agilent.com/ contain tips, discussions and programming examples from other users.

FAQ 2010-03-10

What is the voltage and current limit setting for U8001A and U8002A upon powered up?
Same as the setting before power cycle.

FAQ 2010-02-01

How can I make U8001A or U8002A to be in Output On stage upon powered up?
Order option AUT.

FAQ 2010-02-01

Is there any variations in up/down-programming times from channel to channel in E3646A, E3647A, E3648A and E3649A?
Channel to channel up/down-programming variations time is less than 30ms

FAQ 2009-08-06

Does the Agilent Measurement Manager (AMM) run on Window Vista operating system?
Yes. The Agilent Measurement Manager (AMM) rev. 1.8.3.0 and above will able to run on Windows Vista ...

FAQ 2009-06-10

How can noise be superimposed on the output of a dc power supply?
Agilent power supplies are designed to have the lowest noise that is practically possible. For some applications it is desirable to simulate the effect of noise on the output, for example to test system immunity to power line disturbances.

FAQ 2009-04-15

662xA: Replacing GPIB Printed Circuit Board Assembly

FAQ 2009-03-30

Does the Agilent Measurement Manager (AMM) support regional language settings other than English (US)?
Yes, the Agilent Measurement Manager (AMM) supports regional language settings other than English (US)….

FAQ 2009-01-12

Which of the E36xxA power supplies can be controlled from the remote interface?
The Agilent E3631A, E3632A, E3633A, E3634A, E3640A, E3641A, E3642A, E3643A, E3644A, E3645A, E3646A, E3647A, E3648A, and E3649A power supplies are fully programmable and you can program them from the RS-232 or GPIB (IEEE-488) interface. Both remote...

FAQ 2008-09-23

How do I adjust the voltage or current settings when the Output is disabled on an Agilent E36xxA-Series power supply?
When the Output is disabled, press the 'Display Limit' button on the front panel to place the power supply in the limit mode. Then, set the limit values for the output voltage and current. Press the 'Output Off' button again to enable the power su...

FAQ 2008-09-23

How can I clear the content of power supply memory for programmable E36xxA power supplies?
There is no way to clear the contents of the store/recall states. They can be overwritten as many times as desired but there is not an explicit way to delete saved states.

FAQ 2008-09-23

How much internal memory is available to the user in the E363xA and E364xA power supplies?
The E3631A, E3632A, E3633A and E3634A have 3 non-volatile recall states for the output parameters, each of which can store the voltage, current limit and over-voltage protection setting.

FAQ 2008-09-23

Previous 1 2 3 4 5 6 Next