|
|
|
60xxA, 66xxA and 663xx: Transient Current Overshoots above the Current Limit Setting for Power...
Transient Current Overshoots above the current limit setting for power
|
2005-02-14
|
FAQ
|
|
|
|
|
66xxA and 68xxB: Power Supply Remote Shut-Off
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA and 68xxB: Remote Inhibit
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA and E36xxA: Determining Power Supply Constant Current Mode
The power supply cannot be "put" into the constant current mode.
|
2005-08-03
|
FAQ
|
|
|
|
|
66xxA and E36xxA: P-P Voltage Noise Versus RMS Noise
Both Vp-p and Vrms are measures for the unwanted AC components of a DC power supply output. Peak-to-peak noise is measured from the maximum positive point on the waveform to the most negative voltage point.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA and E36xxA: Programmable Current Sinking
In general, current sinking is a fixed value at some percentage of the full scale current output. However, there is an exception for one series of Agilent power supplies. On the 663xB series, the maximum negative current tracks the value programmed for the positive current limit.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA, 68xxA and E36xxA: Switching vs. Linear Power Supplies
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA, 68xxB and N330xA: Power Products Memory
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA, 68xxB and N330xA: Single Phase Power from a 3 Phase Line
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA, 68xxB, E36xxA and N330xA: Power Supply Cooling Requirements
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA, 68xxB, N330A and E36xxA: Determining the Correct Line Voltage Option to Order for a Power...
Some power products use lots of power, far beyond the range of typical electronic products with which we are familiar. This makes choosing the correct line voltage option more challenging.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA, E362xA, E363xA, E364xA: DC Power Supplies Connecting in Series or in Parallel
The resultant voltage for series connections cannot exceed the maximum floating voltage allowed for any on the component power supplies. While this is typically +/-240 volts dc, there are some supplies as low as +/-25 volts dc, and others as high as +/-550 volts dc.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA, E363xA and E364xA: Can Agilent Power Supplies Sink Current?
Yes! Sinking, or down-programming, is the ability to pull current into the positive terminal of a power supply.
|
2004-06-08
|
FAQ
|
|
|
|
|
66xxA, E435xB, 605xB, N3300A and E36xxA: 'Floating' the Output of a Power Supply Above Ground
66xxA, E435xB, 605xB, N3300A and E36xxA: 'Floating' the Output of a Power Supply Above Ground
|
2006-10-21
|
FAQ
|
|
|
|
|
66xxA: Calibration Certificates
Criteria have been established to determine which products get or do not get a calibration from the factory. A product with a product number does not automatically qualify for a calibration certificate.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA: Down programming
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA: Power Supplies with Inductive Loads
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA: Power Supply Readback Intermittently Corrupted or Empty
|
2002-06-27
|
FAQ
|
|
|
|
|
66xxA: Re-Calibration Date
There are no components used in Power Products which have a specific shelf life. Therefore, the calibration period of this instrument begins on the date that the product is first put into service by the customer. The recommended calibration interval for most Power Products is 12 months.
|
2008-09-22
|
FAQ
|
|
|
|
|
66xxA: Synchronize Different System Power Supply Outputs
|
2002-06-27
|
FAQ
|
|
|
|
|
Can Agilent power supplies be programmed from 0 to full output voltage using a 0 to 10V signal source?
Yes, many Agilent power supplies feature remote voltage programming or analog programming capability. However, there is a potential danger in analog programming any power supply, especially a high voltage supply...
|
2006-04-11
|
FAQ
|
|
|
|
|
For N6700 series power supply, can the option 054 be upgraded after purchase?
Sorry, but the only solution is to order a new module with Option 054 High-Speed Test Extensions. Currently Agilent doesn't stock any hardware or software to add options to modules after the customer orders it.
|
2008-08-18
|
FAQ
|
|
|
|
|
How can I offset the voltage drop caused by long cable lengths from my dc power supply to the device under test (DUT)?
Normally, Agilent power supplies are delivered configured to deliver their full specs at the output terminals. In some application, where long lead lengths to the DUT are unavoidable, the regulation of the power supply at the DUT can be significantly improved by using remote sensing...
|
2007-06-01
|
FAQ
|
|
|
|
|
How do I get Instrument Drivers for Agilent Test & Measurement Products?
From the CD shipped with the instrument or from the product technical support web page for the instrument.
|
2009-05-01
|
FAQ
|
|
|
|
|
What does the LGA option on the N6751A and N6752A modules offer?
The LGA option is strongly recommended on the N6751A/52A modules. The LGA option stands for Large Gate Array.
|
2007-09-13
|
FAQ
|
|
