|
|
PDF
70 KB
|
802.11a WLAN Driver Amplifier using PHEMT ATF-54143 Transistor
This Application Note presents a driver amplifier design using the Agilent Technologies ATF-54143 low noise enhancement mode PHEMT.
|
2002-06-01
|
Application Note
|
|
|
|
PDF
380 KB
|
Analyzing Infiniium Scope Radar Waveform with ADS
This AN focuses on using both Agilent test and measurement instruments such as oscilloscopes, signal generators, and signal analyzers to solve a common design problems of wireless and wireline communications products.
|
2003-12-01
|
Application Note
|
|
|
|
PDF
129 KB
|
Application Note on Tolerance In Surface Mount Varactor Diodes
A Note on the new feature (i.e. tolerance in the nominal capacitance) added to selected models in the Modelithics Non-Linear Diode (NLD) Model Library to emulate variations specified in data sheets.
|
2006-05-25
|
Application Note
|
|
|
|
PDF
868 KB
|
CMOS VCSEL Driver Design Using ADS
This Application Note presents VCSEL laser driver design using a .13um CMOS process with 8 copper metalization layers.
|
2001-09-20
|
Application Note
|
|
|
|
PDF
496 KB
|
Connector and Backplane Capabilities for High-Speed (10 Gb/s) Applications
This Application Note written by Drew Plan and Marco Munguia (Agilent Technologies) describes the path to 10 Gb/s connector and backplane capabilities for High-Speed applications in detail.
|
2006-05-25
|
Application Note
|
|
|
|
PDF
469 KB
|
Creating Measurement-Based Amplifier Behavioral Models
This Application Note describes a behavioral model used in circuit and system simulations to verify performance of the amplifier within a circuit or system.
|
2003-10-01
|
Application Note
|
|
|
|
PDF
245 KB
|
Design of a 4.9 to 6.0 GHz Two-Stage Low Noise using ATF-551M4 E-PHEMT
This Application Note examines the design of a compact two-stage, low noise, unconditionally stable, amplifier for 802.11a, HiperLAN2 and HiSWANa receiver applications using ATF-551M4 E-PHEMT.
|
2005-02-01
|
Application Note
|
|
|
|
PDF
1.24 MB
|
Designing High Speed Backplanes Utilizing Physical Layer Test System
This Application Note focuses on the problems introduced into the backplane assembly design by the many linear passive components that create reflections due to impedance discontinuities.
|
2006-01-18
|
Application Note
|
|
|
|
|
EM Insights Series
This page contains a series of application examples that demonstrate how EM tools can be used to solve actual design problems.
|
2009-05-21
|
Application Note
|
|
|
|
PDF
628 KB
|
Generating Custom, Real-World Waveforms
This Application Note presents how design software and test instrumentation can be used together to create and analyze newly-developed 3G signal formats.
|
2000-10-01
|
Application Note
|
|
|
|
PDF
214 KB
|
Helpful Hints for using Agilent's Advanced Design System (ADS)
This Application Note presents ten helpful hints for using Agilents Advanced Design System (ADS).
|
1998-01-01
|
Application Note
|
|
|
|
PDF
582 KB
|
Linearization of Multi-Carrier Power Amplifier via Digital Predistortion in ADS
This Application Bulletin describes a method for using digital predistortion in Advanced Design System with the Linearization Design Guide to minimize spectral regrowth in wireless systems.
|
2009-03-19
|
Application Note
|
|
|
|
|
Load Pull + NVNA = Enhanced X-Parameters for PA Designs
With high mismatch and technology-independent large-signal device models.
|
2009-05-22
|
Application Note
|
|
|
|
PDF
63 KB
|
Low Noise Amplifier for 3.5 GHz using the Agilent ATF-35143 Low Noise PHEM
This Application Note describes a low noise amplifier for use in the 3.4 GHz to 3.8 GHz wireless local loop, wireless broadband access, and digital microwave radio markets.
|
2002-01-01
|
Application Note
|
|
|
|
PDF
72 KB
|
Low Noise Amplifiers using ATF-55143 Low Noise PHEMT
This Application Note describes two low noise amplifiers (5.125 - 5.325 GHz and 5.725 - 5.825 GHz) for use in the IEEE 802.11a, ETSI/BRAN HiperLAN/2 5GHz standards.
|
2002-05-15
|
Application Note
|
|
|
|
PDF
233 KB
|
Performing Bit Error Rate Measurements with ADS and Baseband Studio Streaming
This Connected Solutions Application Bulletin shows how to verify RF BER performance when a large number of data bits are required to achieve a statistically meaningful BER result.
|
2009-03-19
|
Application Note
|
|
|
|
PDF
270 KB
|
Performing Digital-IF/RF-Digital Bit Error Rate Measurement
This AN describes how to use Agilent Instruments and ADS EDA software to verify RF performance measures such as BER and EVM for end-to-end digital-IF/RF-digital systems--from bits in to bits out.
|
2004-03-12
|
Application Note
|
|
|
|
PDF
1.87 MB
|
Polyharmonic Distortion Modeling
|
2006-06-01
|
Application Note
|
|
|
|
PDF
5.49 MB
|
Practical RF Amp. Design Using the Available Gain Procedure & the ADS EM/Circuit Co-Sim. Capability
This white paper features a method of designing a low noise RF amplifier for an 802.11b receiver application and contains an Avago ATF54143 PHEMT transistor.
|
2009-06-25
|
Application Note
|
|
|
|
PDF
804 KB
|
RF/IF -To- Digital Connected Solutions Bit Error Rate Using Agilent's ADS
This Application Note describes how test and measurement hardware and EDA software from Agilent Technologies can be connected to verify Bit Error Rate for RF/IF-to-digital receiver topologies.
|
2009-03-20
|
Application Note
|
|
|
|
PDF
1.07 MB
|
S-Parameter Techniques for Faster, More Accurate Network Design
The Application Note illustrates the S-Parameter techniques for faster and more accurate network designs.
|
1996-01-01
|
Application Note
|
|
|
|
PDF
275 KB
|
Using ADS for Signal Integrity Optimization
This white paper shows how to replace a multi-dimensional sweep of a long running PRBS time-domain simulation (including manual data evaluation) by short, channel-pulse characterization in the Advanced Design System to efficiently optimize a channel.
|
2009-10-19
|
Application Note
|
|
|
|
PDF
4.25 MB
|
Using Advanced Design System to Design an MMIC Amplifier
This AN illustrates the design of a MMIC amplifier, problems faced in designing, simulating, and producing a physical layout of an MMIC circuit, validation steps needed to verify that the physical layout.
|
2003-06-17
|
Application Note
|
|
