Contact an Expert

Technical Support

Test & Measurement

Find by Product Model Number: Examples: 34401A, E4440A

Refine the List

remove all refinements

By Topic

By Type of Content

By Product Category

1-25 of 52

Sort:
How many capacitance measurement units (MFCMUs) can be installed in the B1500A?
Only one MFCMU can be installed in a B1500A mainframe.

FAQ 2012-06-07

[B1542A] Do not use a base line voltage of gate pulse exceeding +/- 3V range
Do not use a base line voltage of gate pulse lower than -3 V or larger than +3 V to avoid a potential risk of damage on the pulse divider used in the gate cabling system.

FAQ 2012-01-11

[B1542A] What is the maximaum volatge range of gate pulse?
The maximum voltage rage of gate pulse supported by the B1542A Ultra Narrow Pulsed IV solution is -Pulse top: -4.5 V to + 4.5V, -Pulse base::-3 V to +3 V, -Amplitude: 4.5 V or less.

FAQ 2011-11-17

[B1542A] Dose 81130A supported by the B1542A Ultra Narrow Pulsed IV solution?
No.

FAQ 2011-11-17

What is required to run EasyEXPERT 4.2 or later?
Click the above link for details.

FAQ 2011-10-26

What is required to run EasyEXPERT 3.2 to 4.11?
The software requirements of EasyEXPERT 3.2 to 4.11 are as follows.

FAQ 2011-10-26

Does Agilent provide the upgrade product for OS of B1500A from XP to Windows 7?
No, it doesn't.

FAQ 2011-10-26

Can I transport my 4155 and 4156 measurement setups over to the B1500A?
Yes.

FAQ 2011-09-08

If I purchase additional modules for my B1500A can I install them myself?
Agilent does not recommend user self-installation of modules.

FAQ 2011-04-12

Where can I find system requirements for Desktop EasyEXPERT?
System requirements for Desktop EasyEXPERT can be found in the B1500A data sheet.

FAQ 2011-02-15

Can I use Curve Tracer Mode on the B1500A?
Yes. EasyEXPERT 4.0 or later supports Curve Tracer Mode on the B1500A.

FAQ 2011-02-15

Can I control an Agilent 4284A/E4980A using my B1500A to make CV measurements and display the results in the EasyEXPERT data display window?
Yes.

FAQ 2011-02-15

I need to do a system recovery on my B1500A. How should I back up my data?
You can use the Microsoft Windows Backup utility to perform a data backup.

FAQ 2011-02-15

Does the B1500A have switching matrix drivers?
Yes.

FAQ 2011-02-14

Can I rearrange the order of the modules in my B1500A?
No.

FAQ 2011-02-14

How do I recover my B1500A in case I have a problem? I did not receive a Windows OS recovery CD with my instrument.
There is no windows recovery CD supplied with the instrument.

FAQ 2011-02-14

Prober Drivers of B1500A
Prober drivers to control semi-automatic prober from the B1500A.

FAQ 2010-10-01

Does the B1500A have any wafer prober drivers?
Yes.

FAQ 2010-10-01

Can I perform routine Microsoft Windows updates on my instrument’s OS via the internet?
The effects of performing a Microsoft Windows update on the B1500A software or firmware cannot be predicted ahead of time.

FAQ 2009-10-20

If I purchase additional modules for my B1500A do I also have to pay to have Agilent install them?
Yes.

FAQ 2009-10-15

Microsoft Windows Security Updates
Download Microsoft Windows security updates

FAQ 2009-05-27

How do I determine my B1500A’s EasyEXPERT software revision?
You need to open the “Configuration” window to view this information.

FAQ 2009-03-01

I want to use the SMU CMU Unify Unit (SCUU) with a B1500A. Are there any restrictions on the SMU configuration?
The B1500A SMUs are installed in a fixed order starting at the bottom and working up towards the top. The installation order is as follows...

FAQ 2009-03-01

Can I make repeat measurements on the B1500A?
Yes.

FAQ 2009-03-01

Does Agilent I/CV have a driver for the B1500A?
No.

FAQ 2009-03-01

1 2 3 Next