Sprechen Sie mit einem Experten

Technical Support

Test & Messtechnik

Find by Product Model Number: Examples: 34401A, E4440A

Refine the List

Alle detailierte Suchkriterien entfernen

Nach Applikation

By Type of Content

51-70 of 70

Sort:
Dealing with Board Thickness Variations
The Agilent 5DX has the capability to be implemented such that it can accommodate thickness variations on a board-by-board basis. NOTE: Content described is in the 5DX Reference Guide but is no longer in Chapter 7 as mentioned herein.

Application Note 2001-05-16

PDF PDF 31 KB
A Quality Test Demands A Quality Fixture
A Check List for getting a quality board test fixture first time, every time.

Application Note 2001-05-16

PDF PDF 26 KB
Improved Fault Coverage in a Combined X-ray and In-Circuit Test Environment
Cutting functional test failures in half and doubling the faults detected at process test! These are some of the case study results observed in combined X-ray and in-circuit test environments.

Application Note 2001-02-27

PDF PDF 575 KB
Electrical In-circuit Test Methods for Limited-access Boards
This paper surveys the various electrical test methods and tools available to address testing boards that lack full electrical access.

Application Note 2001-02-27

PDF PDF 47 KB
Use of Wrong Thickness Technique Gives Bad Test Results
Beginning with release 6.0, there are two techniques for measurement of solder thickness on the Agilent 5DX, each based on use of a different Confirmation & Adjustment panel.

Application Note 2000-12-31

The Why, Where, What, How, and When of X-ray Test
How do the different AXI technologies work? What are the appropriate uses of 2D vs 3D X-ray? Where in the mfg process should AXI be placed? How can AXI be used to improve the mfg process?

Application Note 2000-11-01

PDF PDF 1.30 MB
Learned Data for the 5DX
The Agilent 5DX uses learned data in several ways to improve algorithm performance. There are basically 2 different forms of learned data.

Application Note 2000-11-01

Product Comparison: the E8285A CDMA Mobile Station Test Set versus the 8924C CDMA Mobile Station...
The Agilent 8924C Option 601 CDMA Mobile Station Test Set and E8285A CDMA MS Service Test Set act as calibrated, high performance base stations to provide the essential set of measurements required to test the parametric and functional characteristics of dual-band, dual-mode CDMA phones. This...

Application Note 2000-04-01

PDF PDF 727 KB
Sprachen 
Reducing Load Time for Loaderless Systems
For Series 2L systems, it may be possible to reduce the time it takes to load a panel.

Application Note 1999-12-01

Printed Circuit Board Split-Pad Test Method and Design
This application note describes the split-pad concept for use with a bed of nails style test fixture.

Application Note 1999-06-01

PDF PDF 50 KB
NDF and RTF - Hashed Names
There have been many questions about hashed directory names. This is a brief explanation of why they are, and how they are generated.

Application Note 1998-06-30

Boundary-Scan Technology, Justification, and Test Implementation for Designers
This paper provides practical insight for designers on the merits, design, and test implementation of Boundary-Scan Technology.

Application Note 1998-05-27

PDF PDF 29 KB
Use of the Test Results Command Processor
TRCMDPRO processes the results from the Agilent 5DX in a way that is specified by a command file. This file is TRCMDPRO.CMD. In addition to the software revisions named, the document applies to all 5DX software versions.

Application Note 1998-01-12

PDF PDF 20 KB
Pharmaceutical Process Control
In this Application Note following the description of the pharmaceutical process control, application measurement and control requirements for characterizing the process are discussed. Then, Agilent VXI-Based data acquisition equipment suitable for such an application is listed. Description...

Application Note 1997-11-01

PDF PDF 113 KB
Rolling Mill
In this Application Note following the description of the rolling mill application, measurement and control requirements for characterizing the process are discussed. Then, Agilent VXI-based data acquisition suitable for such an application is listed. Description Steel, aluminum, fiberglass...

Application Note 1997-11-01

PDF PDF 82 KB
Canning Process Characterization
Following the description of the canning process application, measurement and control requirements for characterizing the process are discussed, then in this Application Note, Agilent data acquisition equipment suitable for such an application is listed. Description In the canning industry...

Application Note 1997-11-01

PDF PDF 94 KB
Pilot Plant Monitoring
In this Application Note following the description of the pilot plant monitoring application, measurement and control requirements for characterizing the process are discussed. Then, Agilent VXI-based data acquisition equipment suitable for such an application is listed. Description Pilot plants...

Application Note 1997-11-01

PDF PDF 120 KB
Appliance Testing
In this Application Note following the description of the appliance testing application, measurement and control requirements for characterizing devices are discussed. Then, Agilent VXI-based data acquisition suitable for such an application is listed. Description Household and commercial...

Application Note 1997-11-01

PDF PDF 110 KB
3070 Increasing Throughput
There are decisions one can make that causes an Agilent 3070 test program to be slower or faster than what Test Consultant generates automatically. This paper offers many tips about how to optimize your system's performance.

Application Note 1997-03-03

PDF PDF 41 KB
How To Float, or Series, Agilent 3070 DUT Supplies
The Agilent 3070 development software does an amazing job of calculating the wiring needed to build fixtures. Even so there are occasionally cases which require wiring that the standard Agilent 3070 software can not handle.

Application Note 1997-01-23

PDF PDF 34 KB

Previous 1 2 3