기술 지원
데이터 수집 하드웨어 및 시스템 전환
상세분류 제거1-25 / 87
|
What is the maximum total length of the RJ45 control cable for connecting multiple 34945EXTs?
The maximum total length of the RJ45 control cables is 140 feet.
FAQ 2013-05-06 |
|
|
What can I do if the Agilent USB Modular Instrument driver installations failed to complete installation on a Windows 7 environment?
If you encountered the event mentioned above, follow the installation best practices steps below.
FAQ 2012-07-25 |
|
|
What can I do if I fail to establish hardware connection after successfully installing Agilent USB modular instrument driver on a Win7 environment?
If you encountered the event mentioned above, follow the installation best practices steps below.
FAQ 2012-07-25 |
|
|
How many Agilent 34970A data acquisition units can be connected to a single PC at a time?
Only one Agilent 34970A can be connected for each RS-232 port on the PC. A GP-IB cable can be used to connect up to 15 units if the GP-IB cable is being referenced by the VEE software. The Benchlink Data Logger 3 software can support up to 4 units...
FAQ 2012-01-25 |
|
|
The Agilent 8761B SPDT Coaxial Switches are not listed in the "Agilent 34945A, L4445A and L4490A/L4491A Configuration Guide". Why?
Due to the 8761B’s internal design the RF path selection is achieved via DC polarity reversal across the coil control terminals. The Agilent 34945A, L4445A and L4490A/L4491A Control Units do not provide a polarity reversal mode. Thus the 8761B cannot be controlled by the 34945A, L4445A and L4490A/L4491A Control Units.
FAQ 2011-12-19 |
|
|
Can the same type modules be paired together to open/close corresponding switches at the same time?
Yes, here are a couple of examples:
The N2280A (Quad 1x2) can be configured as two wire 1x2s using the "card pair" command.
The N2281A (Dual 1x4) can be configured as 2x4s using the "card pair" command.
FAQ 2011-07-27 |
|
|
34970A: How do I add a DMM to a 34970A that does not have one installed?
Order the customer installable retrofit kit 34970-80100.
FAQ 2010-10-12 |
|
|
How can I input 28V digital signal to U2651A/U2652A when it support digital input voltage < 24V?
You can connect a voltage divider in front of the digital input to reduce the voltage to <24V
FAQ 2010-10-07 |
|
|
A Windows® Logo warning message appears during the U2300A Series driver installation. What does this mean?
The Windows® Logo warning message appears if the U2300A Series driver does not have Microsoft® Windows® Logo certification...
FAQ 2010-09-08 |
|
|
Where can I get the drivers for the U2300A Series USB Data Acquisition (DAQ) devices?
The drivers for the U2300A Series Data Acquisition (DAQ) devices are available on the Agilent website….
FAQ 2010-09-08 |
|
|
Matlab throw this error with U2300A/U2500A
"??? Error using ==> daqhwinfo at 115
Failure to find requested data acquisition device: agilentu2500....
Please check whether your Matlab adaptor is installed at the following path:.....
FAQ 2010-08-09 |
|
|
If I set Channel 1 of U2300A/U2500A with voltage range of 5V, I get a reading of 4.99968 when nothing is connected to the DAQ.
If you don't have anything connected to the DAQ and you do an acquisition out of it, the result…
FAQ 2010-08-09 |
|
|
Why is my acquired data for U2300A and U2500A shifted? eg. Column 2 data is in column 1, column 3 data is in column 2, and so on.
Install DAQ hardware driver version 1.05 and above.
FAQ 2010-08-09 |
|
|
I get error from the example "C:\Program Files\Agilent\RF Switch Driver\Examples\VS.NET\CSharp\Example1".
The temporary solution to this is to load the U2931A .dll file that was not loaded with the...
FAQ 2010-07-18 |
|
|
What is the clock rate for Digital Inputs(DI) and Digital Outputs(DO) of U23xxA and U25xxA USB Data Acquisition?
The DAQ DIO is not meant to measure DI with clock rate precision or to control frequency of digital output
FAQ 2010-07-18 |
|
|
Transferring Data and Configurations to a new version or to a new computer
Moving between computers with same version or moving configurations and data to a new version on the same computer...
FAQ 2010-05-07 |
|
|
How many instruments can I have in a configuration?
You can have up to two 34980As or four 34970As in a configuration
FAQ 2010-05-05 |
|
|
Can I rename an instrument instead of using the default Instr1, Instr2... naming convention?
Yes. Click on InstrN in the Name column of the “Configure Instruments” tab and enter a new instrument name.
FAQ 2010-05-05 |
|
|
How can I move a complete configuration from one PC to another?
You can do this by creating a package, move the package to the new PC then read the package in.
FAQ 2010-05-05 |
|
|
How do multiple instruments affect the scan list?
Multiple instruments are integrated seamlessly into a scan list.
FAQ 2010-05-05 |
|
|
Why USB modular instruments (U272XA, U2741A, U2751A and U2761A) is not detectable by E5813A?
PC is failed to enumerate the USB modular instrument.
FAQ 2010-04-09 |
|
|
Transferring Data and Configurations to a new version or to a new computer
Moving between computers with same version or moving configurations and data to a new version on the same computer:
FAQ 2010-03-30 |
|
|
Is there any special setting that I need to do in Agilent VEE before using the U2300A or U2500A DAQ with it?
Yes. In fact it is the most important thing you need to set before using the DAQ with Agilent VEE. As most instruments uses MSB byte ordering, DAQ...
FAQ 2009-12-15 |
|
|
I've written my own text format for SCPI in *.txt. How do I use these for SCPI completion within VEE 9.0. What tool should I use?
You can use the tool found within Agilent.com. Just search using the keyword "Agilent VEE SCPI...
FAQ 2009-11-12 |
|
|
VEE 9.0 has SCPI completion. How do I make my own SCPI command built-in with VEE?
Please refer to the attached Microsoft Word document for a step by step explanation...
FAQ 2009-11-12 |
|
myAgilent에 등록
제품 등록
왜 애질런트 일까요?