Contact an Expert

Technical Support

Test & Measurement

Find by Product Model Number: Examples: 34401A, E4440A

201-225 of 305

Sort:
If the J8130A must be purchased separately what are the required options to use it with the scope?
No extra options are required on the J8130A to run with the MSO6000. The plain J8130A product is sufficient. However, the J8130A has a few potential options that could be ordered if needed: -The option 001 allows the VPT1000 to be used as a Flex...

FAQ 2008-02-12

Does the option FRS or the N5432A for the MSO6000 include the J8130A VPT1000 or must it be purchased separately?
The J8130 (VPT1000) must be ordered separately.

FAQ 2008-01-31

Are additional details available pertaining to the Agilent N4421AK20 or Agilent N4421A-B20 cables?

FAQ 2008-01-29

FAQs: Service Support

FAQ 2008-01-18

What is the minimum size SMD (surface mount device) that the Agilent 16095A probe test fixture can measure?
The 16095A standard probe tip diameter is approximately 1.0 mm...

FAQ 2008-01-14

How can I use the Rear Panel DC Input Connector on my ESA/EMC Series Spectrum Analyzer?
The ESA/EMC will run on DC power via the Option A5D DC Input cables or the E1779A Battery pack.

FAQ 2007-12-20

Can my 33220A be retrofit with Option 33220A-001 External Clock Reference?
Option 33220A-001 External Timebase Reference may be fitted into the Agilent 33220A at any time. The option provides two additional BNC connections for the 10 MHz reference input and output...

FAQ 2007-11-08

What is the part number for the AC power fuse in the N4010A?
Agilent part number 2110-1417.

FAQ 2007-10-29

What's the part number of those multi-pin connector plugs that are on the back of the power supplies?

FAQ 2007-10-15

What replacements are available for the 11664 series of detectors?
The 85025-series of detectors are suitable replacements for use with the 8757A/B/C/D/E family of scalar analyzers…

FAQ 2007-09-14

What are the replacement part numbers for the Obsolete 11664A Scalar Detector connectors?
All components of the 11664-series detectors are obsolete.

FAQ 2007-09-14

What digital probe cables and accessories are available for Agilent mixed-signal oscilloscopes (MSOs)?
The digital probe kit for all Agilent 6000-series and 54620/40-series MSOs is P/N 54620-61801. The digital probe kit for all 8000-series and 54830-series MSOs is P/N 54826-68701.

FAQ 2007-08-10

What hard copy manuals are included with option ABA for the ENA-L?

FAQ 2007-07-12

Is it possible to retrofit option 100, Structural Return Loss, on the ENA-L?
Yes. E5061AU-100 is available to upgrade Opt.100 for ENA-L.

FAQ 2007-07-10

What is the replacement for the Agilent 11764A drive cable?
11764-60004

FAQ 2007-07-06

Do I need to use the side support brackets that came with my N9039A RF Preselector?
Yes. See FAQ content for details...

FAQ 2007-05-31

What probes are available for my logic analyzer?
Agilent offers the following four basic categories of logic analyzer probes...

FAQ 2007-03-23

What are the default calibration kit selections on the 4395A and 4396B Combination Analyzers?

FAQ 2007-03-13

What is the part number of the Agilent WCDMA TEST uSIM?
The part number of the USIM changes periodically, it can be found at www.agilent.com/find/usim. This is a dual format WCDMA and GSM TEST SIM.

FAQ 2007-02-23

On the Agilent 4291A/B Impedance Analyzer, can I utilize a Standard Network Analyzer Calibration Kit to perform the test head calibration?
Test head calibration on the Agilent 4291A/B impedance analyzer is only supported with the included 4291A/B standards.

FAQ 2007-02-15

Can I purchase a rackmount kit for my N4010A?
Yes. The part number for the rackmount kit is 5063-9241.

FAQ 2006-12-21

What replacement parts and accessories are available for the 113xA-series InfiniiMax probes?

FAQ 2006-10-18

What type of cable is supplied with the Agilent 34905A and 34906A dual 4-channel RF multiplexers?
An 18 inch cable with SMB to BNC connectors is supplied.

FAQ 2006-10-17

What features and accessories are included with the standard E7495B Wireless Base Station Test Set?
The standard instrument includes the Antenna Tester/Cable Fault Analyzer and Spectrum Analyzer modes, an Internal GPS Receiver, Accessories, and more. Click here for more details.

FAQ 2006-09-05

What is the Agilent Part Number for the Agilent PNA Series Network Analyzer Bias Tee Input Fuse?
The replacement part number for the PNA Series Network Analyzer bias tee input fuse is Agilent part number 2110-0046.

FAQ 2006-08-11

Previous 1 2 3 4 5 6 7 8 9 10 ... Next