Contact an Expert

Technical Support

Electronic Measurement

Find by Product Model Number: Examples: 34401A, E4440A

51-75 of 305

Can the 16338A be used with LCR meters such as the 4263B and the E4980A?
No, the 16338A Test Lead Set doesn’t have compatibility with LCR meters. The 16338A can be used with the 4338A/B only.

FAQ 2011-06-07

How should a DC blocking capacitor be inserted between the 42941A probe and a DUT when a live DC voltage exists on the device?
It is recommended to insert a SMA DC blocking adapter between the furnished pin probe and 3.5-mm connector at the tip of the 42941A.

FAQ 2011-06-07

What is the interface cable or adapter required to control external GPIB equipment by using VBA macro function of the E4991A?
The 10833A/B/C/D, 82357A or 82357B is required depending on the OS version of the E4991A.

FAQ 2011-06-07

What is the possible cause of the difference when the permittivity measured with the 16453A is different from the value previously obtained?
Most likely cause of the measurement discrepancy or drift is insufficient electrode pressure due to improper pressure adjustment.

FAQ 2011-06-07

Can the 42941A probe be substituted for discontinued 41941A/B probe?
No, the 42941A cannot be substituted for the discontinued 41941A/B and doesn’t have compatibility with old 4194A analyzer.

FAQ 2011-06-07

Why is permeability measurement result unstable when a low permeability magnetic material or a thin magnetic material is measured with the 16454A?
It is because the impedance of the magnetic material inserted into the 16454A is too low for the impedance analyzer to measure it accurately.

FAQ 2011-06-07

How can the E4980A or the 4263B measure internal impedance of batteries?
Insert DC blocking capacitors between the measurement terminals and a battery DUT. The 16065C can substitute for the DC blocking capacitors.

FAQ 2011-06-07

Can the 42941A probe be used with any RF test fixture adapter?
No, the 42941A does not have any test fixture adapter available for connecting the probe to an RF component test fixture.

FAQ 2011-06-07

How do I change the power-line voltage setting of 34401A and what is the corresponding power-line fuse to be used?
The line voltage has been set to the proper value for your country when the multimeter is shipped from the factory...

FAQ 2011-06-05

What additional items are required to utilize the E4991A option 007 Temperature Characteristic Test Kit?
For newly purchased E4991As an Agilent 82357B USB-GPIB card is required as well as a GPIB interface on the temperature chamber. The recommended temperature chamber is an ESPEC model SU-261 temperature chamber.

FAQ 2011-05-31

Can I use the test fixture with B2900A?
Yes. The N1295A device/component test fixture is available for B2900A up to 42V.

FAQ 2011-05-18

What waveguide flanges will the new M1970V and M1970W band external mixers have?
The waveguide flanges for the new M1970V and M1970W (V & W Band) waveguide harmonic mixers will be the same as the current legacy 11970V and 11970W mixers. The V band mixer will be using the WR15 and WR10 will be in the W band mixer.

FAQ 2011-04-26

What is the dielectric constant and material composition of the Agilent 33391C Microwave Insulator Bead Assembly?
The insulator bead is Noryl® modified Polyphenylene Oxide (PPO). The dielectric constant is 2.63-2.68.

FAQ 2011-04-21

Is there an external battery pack for the X-Series (PXA/MXA/EXA/CXA) Signal Analyzer?
Not at initial release.

FAQ 2011-03-24

Do I need a keyboard and mouse to operate the Agilent X-Series (PXA/MXA/EXA/CXA) Signal Analyzers?
No. However, since this is a Windows based instrument it is easier to navigate various windows using a mouse.

FAQ 2011-03-24

How can I get the accessories (cables and adaptors) for measurement setup of the ENA & the E5092A?
All accessories are included in the option of the E5092A.

FAQ 2011-01-20

34970A: How do I add a DMM to a 34970A that does not have one installed?
Order the customer installable retrofit kit 34970-80100.

FAQ 2010-10-12

I lost some of the small parts of the N1021B probe kit. Can I get them without buying a whole kit?
The following items will be available from ...

FAQ 2010-09-19

Which MXG signal generator parts are customer-replaceable?

FAQ 2010-09-19

What is the difference between a standard coaxial connector and precision slotless connector (PSC)?
Precision slotless female contacts are used to reduce the reflection uncertainty at a connector interface. Slotless contacts make electrical connection with the mating male pin without changing the outer diameter of the female center conductor.

FAQ 2010-09-08

FAQs: Hardware Configurations and Installation

FAQ 2010-08-27

How many interface cables does the 11713B/C attenuator/driver come with?

FAQ 2010-07-26

Can I use external power adaptor to charge my V3500A handheld power meter?

FAQ 2010-07-18

Do the coaxial Short and 50 Ω Load terminations for the 42941A have accuracy specifications?
No, both the coaxial Short and 50 Ω Load standard terminations for the 42941A do not have accuracy specifications.

FAQ 2010-07-02

Is there any effective way to measure the impedance of a pressure sensitive SMD component (ex. a ferrite bead) with the 16196 series or 16197A test...
In order to measure a pressure sensitive device, the pressure applied to the DUT by the test fixture needs to be carefully controlled.

FAQ 2010-07-02

Previous 1 2 3 4 5 6 7 8 9 10 ... Next