Technical Support

Test & Measurement

Refine the List

remove all refinements

By Topic

All Topics
- Service & Maintenance

By Application

Basics (2)
- Instrument Security (2)

By Type of Content

FAQ (90)

By Product Category

All Product Categories
- Oscilloscopes, Analyzers, Meters
  - Oscilloscopes (15)
  - Spectrum Analyzers (Signal Analyzers) (23)
  - Network Analyzers (12)
  - Handheld Oscilloscopes, Analyzers, Meters (3)
  - Logic Analyzers (13)
  - EMI/EMC, Phase Noise, Physical Layer Test Systems (3)
  - Digital Multimeters (DMM) (2)
  - Power Meters & Power Sensors (8)
  - LCR Meters & Impedance Measurement Products (21)
  - Digitizers (3)
  - Dynamic Signal Analyzers, Materials Measurement (3)
  - Parameter & Device Analyzers, Curve Tracer (1)

1-25 of 90

Is Option A6J or 1A7 calibration available on the X-Series, PSA, ESA analyzers and X-Series, ESG-C, PSG signal generators directly from the factory? Yes, there are additional details for certain PSA configurations that can be found here. FAQ 2013-05-17
Can I order the replacement part of 16089E's clips? When the clip is faulty, please proceed to place a new order on 16089E or purchase the spare Kelvin Clip Leads. FAQ 2013-03-17
How do I upgrade analysis bandwidth on an N9030A PXA Signal Analyzer? Table describes each scenario... FAQ 2013-02-07
How can I tell if my instrument is licensed for Options B1X, B1Y, and MPB? You can check to see what options are installed in your instrument by pressing the [System] hard key, then the {Show} soft key, then the {System} soft key. FAQ 2013-02-07
What option should I order to get RTSA in an existing N9030A PXA signal analyzer? If you already have Option B1X, B1Y and MPB ... FAQ 2013-02-07
Can I use external mixing (Option EXM) with real-time? No, you cannot use external mixing (Option EXM) with real-time. FAQ 2013-02-07
Can I use noise floor extension (NFE) with real-time? No, you cannot use noise floor extension with real-time. FAQ 2013-02-07
Can I upgrade the U8903A Audio Analyzer's firmware myself? you can upgrade the U8903A Audio Analyzer's firmware yourself. FAQ 2013-01-03
Do I need to perform a periodic front panel instrument alignment on my N9039A RF Preselector? No, but there is a system alignment that needs to be periodically run. See FAQ content for details... FAQ 2012-12-11
Is it possible to disable or enable the Automatic Logon for Windows® on the ENA? Yes. To disable or enable the Automatic logon for Windows® in a Non-Domain System, perform the following: FAQ 2012-10-17
What is the difference between an "ECal Confidence Check" and a Network Analyzer "System Verification" test? The ECal Confidence Check is a method to check the accuracy of a calibration performed with either a mechanical cal kit or an ECal module. System verification testing provides network analyzer users a method to verify that the network analyzer is ... FAQ 2012-10-17
Where can I upgrade my existing U8903A to digital audio option? The retrofit upgrade is available in Agilent service support center. FAQ 2012-07-25
Why is the AC to DC power supply for my E7495A/B Base Station Test Set not working? Click here for information about the AC to DC power supply for E7495A/B. FAQ 2012-05-29
How often do I need to run the RF Preselector alignments in my MXE? Every 30 days or when the temperature changes by 3 degrees... FAQ 2012-05-09
How do I declassify or sanitize my 54800-series Infiniium oscilloscope? Follow the procedure below to ensure that your oscilloscope no longer contains any user configurations or data. FAQ 2012-05-09
Is there a connector repair kit available for the 3.5 mm-female precision slotless connector (PSC)? FAQ 2012-05-04
How is the display of the E7495A/B Wireless Base Station Test Set protected from damage? The E7495A/B's display has a Lexan hard coating that is anti-reflective and scratch resistant. An air gap between the outer covering and the LCD display additionally protects the display from impact. FAQ 2012-02-28
What is the frequency range of the N5532A Sensor Module? 100 kHz to 4.2 GHz, 10 MHz to 18 GHz, 30 MHz to 26.5 GHz, and 30 MHz to 50 GHz. FAQ 2012-02-26
Must I return my 89441A Vector Signal Analyzer (VSA) for repair if it displays an "RF LO Unlock" error? If the error message occurs and persists, a failure has occurred in the RF section of the VSA. FAQ 2012-02-25
How do I perform a security erase of my spectrum analyzer memory? Instructions on performing a security erase for spectrum analyzers. FAQ 2012-02-24
Do the handheld spectrum analyzers have record/playback features in the spectrogram and the spectrum mode? Can the signal be recorded on a USB drive? Option SIM for the HSAs provides record and playback features in the spectrogram and the spectrum mode. FAQ 2011-11-07
On the ENA / ENA-L, how do I determine my hard disk version? FAQ 2011-10-07
Why i can't find other languages help file setting in U160X A/B series HH oscilloscope? In order to access to other language, please go to respective product support page in www.Agilent.com. Go to Driver & Software page, select Firmware Update. FAQ 2011-09-12
Does Agilent U1271A/U1272A Handheld Digital Multimeter comes with a power adapter? No, U1271A/U1272A is powered by four 1.5V AAA alkaline batteries. FAQ 2011-05-05
What is the part # of the fuseholder cap for the small Front and Rear Current input fuse 3AT (A1F101 or F101) used on the Agilent 34401A Multimeter... The small Front and Rear Current input fuse 3AT (A1F101 or F101) located on the rear panel is available as Agilent part number 2110-0780. This is a 3A, 250V metric fuse. FAQ 2011-04-14

1 2 3 4 Next

Technical Support

Test & Measurement

Refine the List

By Topic

By Application

By Type of Content

By Product Category

1-25 of 90

Products & Services

Technical Support

Applications & Solutions

About Agilent