기술 지원
테스트 및 측정
상세분류 제거1-25 / 532
|
Replacing the 8508A vector voltmeter with the E5061B network analyzer
Measuring the phase difference of an external CW signals is a typical measurement application of the 8508A vector voltmeter.
FAQ 2013-04-25 |
|
|
ENA 6 시리즈는 주파수 스윕할 때 swept sweep 모드를 지원합니까?
아니요..
FAQ 2013-04-25 |
|
|
어떻게 4294A에서 DUT에 40이상의 DC 전압을 인가할 수 있습니까?
외부 DC 소스와 보호 회로가 필요합니다.
FAQ 2013-04-16 |
|
|
E4438C, E8267D에서 사용할 수 있는 GSP 시나리오 파일들을 어디서 다운로드 받을 수 있나요?
E4438C-409 와 E8267D-409 GPS 옵션에 대한 웹페이지에서 추가적인 시나리오 파일들을 사용해 보실 수 있습니다.
FAQ 2013-02-06 |
|
|
How much jitter is there when using an external trigger?
Unless the trigger signal is synchronized to the Arb sample clock, you will see jitter equal to the sample period for the internal Arb and equal to 8 sample periods for the N6030A.
FAQ 2012-12-30 |
|
|
Is it possible to adjust the phase offset using degrees instead of radians?
Yes. Select View -> Customize Pattern Item Table and toggle the ‘phase offset in degrees’ button
FAQ 2012-12-30 |
|
|
How do you calculate the individual output power of each satellite?
The ESG/PSG power level is distributed equally among the satellites.
FAQ 2012-11-21 |
|
|
Are scenario files compatible between the E4438C-409 and the N7609B?
Yes, the N7609B can use any of the scenario files created for the E4438C-409...
FAQ 2012-11-21 |
|
|
What is the maximum sampling rate for the GNSS waveforms?
The sampling rates vary depending on which constellation is being simulated, and they range from 2.044 MSa/s for GLONASS up to 24.552 MSa/s for Galileo.
FAQ 2012-11-21 |
|
|
How much baseband generator memory is needed in the signal generator to use basic mode waveforms?
The amount of memory that is needed depends on how many waveform files you need to have in the instrument memory at one time.
FAQ 2012-11-21 |
|
|
What is the data content in the single satellite waveform files? Is it real navigation data?
The waveform files contain alternating 0s and 1s for the data. Real navigation data is not included since it is impossible for a receiver to calculate a location fix using only a single satellite signal.
FAQ 2012-11-21 |
|
|
How does the N7609B calculate the total output power in relation to the number of visible satellites during a scenario?
When you initially turn on the simulation, the Satellite Settings page will update the “Power” column to show the power of each satellite in dBm.
FAQ 2012-11-21 |
|
|
Where can I find GLONASS almanac files to create custom scenarios?
You can obtain GLONASS almanac files from this URL: ftp://ftp.glonass-iac.ru/MCC/ALMANAC.
FAQ 2012-11-21 |
|
|
How much baseband memory do I need in the ESG/PSG for opt. 422 scenario generator?
The scenario files reside on the hard drive until one is selected for playback, and then it is loaded into the baseband memory.
FAQ 2012-11-21 |
|
|
Can Agilent provide a location accuracy specification for the Option 409?
Unfortunately, Agilent cannot provide a location accuracy specification because this is dependent on the GPS receiver.
FAQ 2012-11-21 |
|
|
Is there a way to transfer sets of waveforms to each signal generator without having to connect the N7609B software to each instrument?
Yes. All of the waveform files are available on your PC when you install the N7609B application; they are in the application SW folder
FAQ 2012-11-21 |
|
|
Why does my GPS receiver not show the correct year that I’m simulating?
The GPS date is expressed as a week number and a time-of-week value. The week number is transmitted as a ten-bit field in the C/A navigation message. It can therefore signify a week within a period of 1,024 weeks or 19.69 years.
FAQ 2012-11-21 |
|
|
Where can I find Galileo almanac files to create custom scenarios?
There are no official published almanac files at this time for Galileo. The N7609B software includes a default almanac file, 20110709_Gal.alm
FAQ 2012-11-21 |
|
|
When simulating a signal that includes GLONASS and Galileo my receiver is reporting different satellite IDs than shown in the Signal Studio, why?
While GPS satellites are commonly identified by the pseudorandom codes (PRN) that they use, there is no industry standard yet for how to refer to the GLONASS or Galileo satellites.
FAQ 2012-11-21 |
|
|
I’m using the N7609B with an X-series signal generator. Can I generate a real-time GNSS signal without being connected to Signal Studio?
Yes, if you are using a stored scenario file, but not if you are using continuous scenario generation mode.
FAQ 2012-11-21 |
|
|
Where can I find GPS almanac files to create custom scenarios?
You can obtain GPS almanac files from this URL: http://www.navcen.uscg.gov/?pageName=gpsAlmanacs
FAQ 2012-11-21 |
|
|
How do I obtain the NMEA GGA message file of trajectory information in order to create a dynamic scenario for a moving GNSS receiver?
There are several ways to do this...
FAQ 2012-11-21 |
|
|
Can MXG or EXG support more than 2 USB power sensors?
EXG and MXG X-Series signal generators are only able to display the measurements from 2 USB sensors at the same time.
Up to 4 USB sensors can be connected (since we have 4 USB ports on N5181B, N5182B, N5171B, N5172B), but only 2 are actively displayed simultaneously. The user would have to swap in/out the USB sensors that they want to read, via the front panel or SCPI.
FAQ 2012-10-25 |
|
|
4294A로 접지된 DUT 측정이 가능 한가요?
4294A로 접지된 DUT 측정이 가능합니다.
FAQ 2012-10-22 |
|
|
Is it possible on the Agilent ENA series Network Analyzers to over-ride the output source blanking at every sweep end?
Yes, the output source blanking on sweep retrace can be prevented by turning off the Initial Source Port Control function.
FAQ 2012-10-17 |
|
myAgilent에 등록
제품 등록
왜 애질런트 일까요?