기술 지원
테스트 및 측정
상세분류 제거1-25 / 1116
|
How do you clear the M9381A PXIe Vector Signal Generator and M9380A PXIe CW Source modules memories?
Please refer to the documents for a comprehensive listing of memory installed into these products.
FAQ 2013-05-20 |
|
|
Will there be specification, performance characteristic or usability differences when using the 11970 Series mixers on the PXA?
Yes, there will be several differences when using 11970 Series mixers with the
FAQ 2013-04-26 |
|
|
Will the PXA work with the N8975AZ-Kxx block down converters for noise figure to 110 GHz?
...will...to...N8975AZ-Kxx...noise...figure...block...converters...with...PXA
FAQ 2013-04-26 |
|
|
ENA 6 시리즈는 주파수 스윕할 때 swept sweep 모드를 지원합니까?
아니요..
FAQ 2013-04-25 |
|
|
M1970V과 M1970W 스마트 믹서의 waveguide flange 타입은 무엇입니까?
기존의 11970V 와 11970W 하모닉 믹서와 동일합니다.
FAQ 2013-04-25 |
|
|
4294A에 ALC(자동 레벨 조절) 기능이 있나요?
아니요, 4294A에는 자동 조절 기능이 없습니다.
FAQ 2013-04-17 |
|
|
E4980A에서 RF 동축 케이블 사용 시 전기적 길이 보상이 필요하나요?
아니요, 필요하지 않습니다.
FAQ 2013-04-17 |
|
|
어떻게 4294A에서 DUT에 40이상의 DC 전압을 인가할 수 있습니까?
외부 DC 소스와 보호 회로가 필요합니다.
FAQ 2013-04-16 |
|
|
How do you clear the M9036A Embedded Controller memories?
Please refer to the link below for the procedure on how to clear the memories for the M9036A Embedded Controller.
FAQ 2013-03-15 |
|
|
How do you clear the M9536A Embedded Controller memories?
Please refer to the link below for the procedure on how to clear the memories for the M9536A Embedded Controller.
FAQ 2013-03-15 |
|
|
What USB storage devices are compatible with the MXG?
The MXG is now compatible with most USB storage devices.
FAQ 2013-03-13 |
|
|
Sample “testplan” for Utility card & FR3070A
Sample “testplan” for Utility card & FR3070A from manufacturing site
FAQ 2013-02-18 |
|
|
E4980A에서 Rdc를 측정할 때 Load correction data가 적용됩니까?
아니요.
FAQ 2013-02-07 |
|
|
GSM/EDGE 기지국 Loop-back 테스트 용 옵션 300을 N5182B MXG 또는 N5172B EXG 인 X-Series 신호 발생기에서도 지원될까요?
지원되지 않습니다.
FAQ 2013-02-04 |
|
|
1세대 MXG 인 N5181A 또는 N5182A를 X-Series 신호 발생기인 N5181B 또는 N5182B로 업그레이드 할 수 있을까요?
불가능합니다.
FAQ 2013-02-04 |
|
|
Which AXIe modules can be controlled using the USB option on the AXIe chassis ESM (M9502A-U20 and M9505A-U20)?
The only modules supported through USB connectivity to a host PC are the following Agilent logic and protocol analyzer modules.
FAQ 2013-01-09 |
|
|
애질런트 8712ES/ET 및 8714ES/ET 벡터 네트워크 분석기에서 트레이스 이미지를 플로피 디스크에 캡처하는 프로세스는 무엇입니까?
8712ES/ET 및 8714ES/ET 벡터 네트워크 분석기는 플로피 드라이브를 통해 HPGL, PCX, PCL5 및 GIF 이미지 저장을 지원합니다.
FAQ 2013-01-07 |
|
|
When would I use ALC Hold?
ALC Hold is used for pulses with rise and fall times greater than 100 ns. It is used with pulses that do not have constant envelope modulation (such as AM Step), and with multiple pulses where the pulses have different amplitudes.
FAQ 2012-12-30 |
|
|
Is there an easy way to save a pulse pattern and send it to another person?
Yes, simply save the entire .pbp or you can export the pattern using the “export pattern” function.
FAQ 2012-12-30 |
|
|
Is it possible to adjust the phase offset using degrees instead of radians?
Yes. Select View -> Customize Pattern Item Table and toggle the ‘phase offset in degrees’ button
FAQ 2012-12-30 |
|
|
Can I turn off the N6030A arbitrary waveform generator predistortion from the N7620B Signal Studio for Pulse Building to get more power?
No. The N7620B software does not allow the N6030A predistortion to be turned off.
FAQ 2012-12-30 |
|
|
How do I change the 10 MHz reference source if Signal Studio for pulse building doesn’t detect the reference?
Most of the time, Signal Studio will recognize the reference; however, it can be changed in the download -> customize menu.
FAQ 2012-12-30 |
|
|
Is there a way to simulate jitter in my pulse pattern?
Yes, Signal Studio for pulse building allows you to add jitter on the pulse width and pulse repetition interval.
FAQ 2012-12-30 |
|
|
Does the Signal Studio for Pulse Building software run on a National Instruments embedded PXI controller like the one that comes with the N6030A?
Yes, it does. However, the Agilent I/O Libraries may need to be installed as a secondary VISA and then the NI Tulip DLL may need to be enabled.
FAQ 2012-12-30 |
|
|
Are there any options to adjust the pulse definitions within Signal Studio for pulse building?
No, at the moment the rise and fall times are defined by their 0-100 percent points and the pulse width is defined to be the 100-100 percent point.
FAQ 2012-12-30 |
|
myAgilent에 등록
제품 등록
왜 애질런트 일까요?