|
Is it possible on the Agilent ENA series Network Analyzers to over-ride the output source blanking at every sweep end?
Yes, the output source blanking on sweep retrace can be prevented by turning off the Initial Source Port Control function.
FAQ
2012-10-17
|
|
|
What is the difference between an "ECal Confidence Check" and a Network Analyzer "System Verification" test?
The ECal Confidence Check is a method to check the accuracy of a calibration performed with either a mechanical cal kit or an ECal module. System verification testing provides network analyzer users a method to verify that the network analyzer is ...
FAQ
2012-10-17
|
|
|
Are there any step-by-step measurement examples for ENA 7 series?
Yes. There are some measurement examples in ENA help file...
FAQ
2012-10-17
|
|
|
Can I make absolute measurements on the ENA?
Yes.
FAQ
2012-09-25
|
|
|
Can I use the Fixture Simulator functions with the 2-port ENA?
Yes, but the function is limited...
FAQ
2012-03-16
|
|
|
Does the ENA 6 series have the swept sweep mode in the frequency sweep?
No. The E5061A/62A and E5061B have only stepped sweep mode in the frequency sweep.
FAQ
2012-03-16
|
|
|
How is trace math implemented within the Agilent Technologies Vector Network Analyzers?
FAQ
2012-01-11
|
|
|
Can the ENA make mixer measurements?
Yes. With option 008 (Frequency-Offset Mode), you can measure frequency-converting devices, such as mixers.
FAQ
2011-10-16
|
|
|
Is there an outline to achieving a simplified mixer conversion loss measurement on the ENA?
Option 008, Frequency offset, is required for mixer measurements utilizing these analyzers.
FAQ
2011-10-16
|
|
|
What will occur if I save touchstone file with different port reference impedance for each port?
The Z0 of the minimum port is selected for the reference port impedance of the saved data.
FAQ
2011-10-16
|
|
|
On mixer measurement with the ENA and external signal source, should I connect frequency references of the ENA and external signal source?
Yes.
FAQ
2011-10-16
|
|
|
When measuring active devices with an external DC power supply, are there any precautions?
Yes. Please be careful of transient voltages.
FAQ
2011-10-16
|
|
|
The "set Zo" function does not appear to affect the displayed S-parameters of my network analyzer. How does this function work?
FAQ
2011-10-07
|
|
|
For Cable Testing should I use a TDR, a network analyzer, or both?
The cable specifications will determine the test equipment requirements...
FAQ
2011-10-07
|
|
|
On the ENA / ENA-L, what occurs if I select "order-based display" in sweep mode?
Measurement points of different segments are plotted in constant intervals.
FAQ
2011-10-07
|
|
|
Using the VBA program, can the ENA / ENA-L control the handler interface to control other peripherals?
Yes.
FAQ
2011-10-07
|
|
|
Does the touchstone file generated by the ENA / ENA-L include the electrical delay?
The touchstone files do not include electrical delay. Please use port extension.
FAQ
2011-10-07
|
|
|
What are the equations that relate Real and Imaginary data pairs to Log Magnitude, Polar, Phase, and Smith Chart formats?
FAQ
2011-10-07
|
|
|
When I save a Touchstone file with the ENA / ENA-L, which calculation will be reflected in the Touchstone file?
All calculations are reflected in the Touchstone file except for the mixed-mode conversion.
FAQ
2011-10-07
|
|
|
Is it possible to change the font size of softkey menu on ENA?
Yes. The font size of softkey menu can be changed with following procedure...
FAQ
2011-10-07
|
|
|
What is the difference between Smoothing and Averaging on an Agilent network analyzer?
FAQ
2011-10-07
|
|
|
What is the difference between "sweep speed", "cycle time" and "time per data point" as related to a vector network analyzer?
FAQ
2011-10-07
|
|
|
On the ENA, how can I make CW sweep (Fixed frequency) without turning off the ENA's output signal each time a sweep finishes?
Turn off the "Init Src Ctrl" feature, then hold trigger.
FAQ
2011-10-07
|
|
|
How can I calculate the equivalent phase delay, as a function of frequency, for a given electrical delay as set on Vector Network Analyzer?
Equivalent phase delay, based upon electrical delay is computed as: θ˚ = Ftest * Delay * 360
FAQ
2011-10-07
|
|
|
How can the S21 to transmission impedance (Zt) conversion equation on the 4395A Operation Manual be derived?
The equivalent circuit model of transmission measurement is as follows.
FAQ
2011-06-03
|
|
remove all refinements
Enroll in myAgilent
Register Your Product
Why Buy Agilent