기술 지원
테스트 및 측정
상세분류 제거1-25 / 154
|
Replacing the 8508A vector voltmeter with the E5061B network analyzer
Measuring the phase difference of an external CW signals is a typical measurement application of the 8508A vector voltmeter.
FAQ 2013-04-25 |
|
|
ENA 6 시리즈는 주파수 스윕할 때 swept sweep 모드를 지원합니까?
아니요..
FAQ 2013-04-25 |
|
|
Is it possible on the Agilent ENA series Network Analyzers to over-ride the output source blanking at every sweep end?
Yes, the output source blanking on sweep retrace can be prevented by turning off the Initial Source Port Control function.
FAQ 2012-10-17 |
|
|
Are there any step-by-step measurement examples for ENA 7 series?
Yes. There are some measurement examples in ENA help file...
FAQ 2012-10-17 |
|
|
Can I make absolute measurements on the ENA?
Yes.
FAQ 2012-09-25 |
|
|
What is the cutoff frequency of the rear AUX input ports?
1V range: 10 kHz, 10V range: 2.7 kHz
FAQ 2012-09-25 |
|
|
2 포트 ENA에서 mixed 모드 S-파라미터 측정이 가능 합니까?
...of mixed mode S-parameters on the 2-port ENA
FAQ 2012-07-29 |
|
|
적합한 임피던스 측정 기술을 쉽게 익힐 수 있는 권장 책자에는 어떤 것이 있습니까?
FAQ 2012-07-17 |
|
|
HP 8712/8714 ET/ES RF Network Analyzers with Option 100 (Fault Location): Finding Cable Loss...
How do I determine cable loss?
FAQ 2012-04-09 |
|
|
Can I use the Fixture Simulator functions with the 2-port ENA?
Yes, but the function is limited...
FAQ 2012-03-16 |
|
|
신호 분석기 기록에서 내게 필요한 내용을 어떻게 더 빨리 찾을 수 있습니까?
신호 분석기 기록이 매우 길면 때때로 관심 부분을 찾기가 어렵습니다. 현재는 이 문제에 실제로 도움이 되는 훌륭한 툴은 없지만 몇 가지 제안사항이 있습니다.
FAQ 2011-12-20 |
|
|
What is an alternative solution to the 87075C / 87050E replacement?
Build your home-made switch box using the L4491A RF/MW switches. Refer to the application note for details.
FAQ 2011-12-09 |
|
|
ENA를 사용하여 50 ~ 75 Ω 임피던스 매칭 디바이스를 측정하는 것이 가능합니까?
50 ~ 75 Ω 임피던스 매칭 디바이스는 ENA의 어댑터 제거/삽입 기능 및 임피던스 변환 기능을 통해 측정될 수 있습니다.
FAQ 2011-10-17 |
|
|
Can the ENA perform Vector Mixer Calibration (VMC) with Fixed RF or Fixed IF measurement?
No. It is not possible to perform Fixed RF measurements (RF: Fixed, LO and IF: Swept) with VMC.
FAQ 2011-10-17 |
|
|
ENA에서 듀얼 변환 믹서를 측정할 수 있습니까?
로컬 주파수가 고정되어 있고, ENA에 옵션 008 (Frequency-Offset Mode)이 있다면 측정가능합니다.
FAQ 2011-10-17 |
|
|
ENA를 사용하여 어떻게 75 Ω 측정을 할 수 있습니까?
ENA를 사용하여 시스템 특성 임피던스를 75 Ω으로 변경시켜 75 Ω 측정을 할 수 있습니다.
FAQ 2011-10-17 |
|
|
Can I use S2P data characterized by the ENA, as the calibration mixer data for Vector Mixer Calibration on the PNA?
For the case of RF mixer (RF=LO+IF), there is no problem. However, when using an image mixer (RF=LO-IF) as the calibration mixer on the PNA, taking the S2P data in the ENA with a special setting is required...
FAQ 2011-10-17 |
|
|
On mixer measurement with the ENA and external signal source, should I connect frequency references of the ENA and external signal source?
Yes.
FAQ 2011-10-16 |
|
|
When measuring active devices with an external DC power supply, are there any precautions?
Yes. Please be careful of transient voltages.
FAQ 2011-10-16 |
|
|
For Cable Testing should I use a TDR, a network analyzer, or both?
The cable specifications will determine the test equipment requirements...
FAQ 2011-10-07 |
|
|
On the ENA / ENA-L, what occurs if I select "order-based display" in sweep mode?
Measurement points of different segments are plotted in constant intervals.
FAQ 2011-10-07 |
|
|
On the ENA, how can I make CW sweep (Fixed frequency) without turning off the ENA's output signal each time a sweep finishes?
Turn off the "Init Src Ctrl" feature, then hold trigger.
FAQ 2011-10-07 |
|
|
85070D/85071D: Microwave Materials Measurements With a Network Analyzer
The necessary items include a network analyzer, a probe or sample holder, and measurement software.
FAQ 2011-10-03 |
|
|
What is the measurement setup for obtaining same spectral levels of measured signal or noise irrespective of the sweep frequency span of the 4395A?
Change the detection mode to sample detection mode.
FAQ 2011-06-03 |
|
|
네트웍 분석기를 사용하여 믹서측정과 관련된 어플리케이션 노트가 있습니까?
.
FAQ 2010-05-17 |
|
myAgilent에 등록
제품 등록
왜 애질런트 일까요?