Contact an Expert

Technical Support

Electronic Measurement

Find by Product Model Number: Examples: 34401A, E4440A

Refine the List

By Topic

By Industry/Technology

By Type of Content

By Product Category

126-150 of 1126

Sort:
For the PSA Series spectrum analyzer, is gated sweep capability required for options 212 (TD-SCDMA Modualtion Analysis) and 213 (HSDPA / 8PSK for T...
No, Gated sweep is not required.

FAQ 2012-05-30

What is the maximum DC input for PSA Series Spectrum Analyzer?
AC/DC coupling values found here...

FAQ 2012-05-30

Can the E4406A or PSA Series cdmaOne personality (Option BAC) make power timing and phase measurements?
Yes. In the cdmaOne personality you will first need to change the Measure Method to Timing and Phase under the Measure Setup key and then change the view to Power Timing and Phase under the View/Trace key.

FAQ 2012-05-29

Does the E7495A/B Base Station Test Set allow simultaneous operation of the CW and complex source in Spectrum Analyzer mode, Channel Analyzer mode,...
Yes. This support was added for A.02.10 firmware in January 2004.

FAQ 2012-05-29

What file formats does the 89601A VSA software support for signal waveforms?
Recorded data from the following files can be interpreted by the 89600: ASCII (.txt and .csv), Binary (89600 SDF .sdf, .dat), Binary (E3238 .cap), Binary (N5510A .bin), MATLAB 7 (or earlier, .mat)

FAQ 2012-05-28

Do the E4406A and PSA Series support Complementary Cumulative Distribution Function (CCDF) measurement for cdmaOne?
Yes. The Power Statistics CCDF measurement is not in the cdmaOne personality (Option BAC), but it does come standard in the Basic measurement personality for E4406A and in the Spectrum Analysis mode for PSA and can be used to measure cdmaOne sign...

FAQ 2012-05-26

Do the E4406A, PSA Series and 89600 VSA Software report Peak Code Domain Error for W-CDMA and cdma2000?
Yes. The screen capture below shows a W-CDMA Modulation Accuracy measurement on the E4406A and PSA Series, and Peak Code Domain Error is reported in the results table.

FAQ 2012-05-26

Which Application Notes are Most Relevant to the PSA Series Spectrum Analyzer?
This page contains links to application notes that are relevant to PSA Series spectrum analyzers.

FAQ 2012-05-11

Can I use the 16092A with the 4395A/4396B/4287A/E4991A?
Yes, you can use the 16092A with the 4395A/4396B/4287A/E4991A.

FAQ 2012-05-10

Why do I get a Meas Uncal message when I select either the Quasi-Peak or EMI Average detector for taking a full band sweep with the MXE EMI Receiver?
Sweeptime has reached its maximum. See complete FAQ for further details...

FAQ 2012-05-10

How do I make the signal list compare measurements made with the detectors used to different limit lines in my MXE EMI Receiver?
Meas Setup, Detectors (Measure)...

FAQ 2012-05-10

What is required to use Remote UI for the E4991A?
You need to prepare the following items: the E4991A, a PC, the E4991A VBA software (E4991A_vba.msi) included in the furnished CD-ROM and, LAN environment. For details, please refer to chapter 10 "Using LAN" of the E4991A operation manual.

FAQ 2012-05-10

How do a take a sweep with both the Quasi-Peak and EMI Average detector at the same time with an MXE EMI Receiver?
Switch to EMI Receiver mode...

FAQ 2012-05-10

How do you clear the M9045A, M9045B, M9047A and M9048A memory?
Please refer to the link below for the procedure on how to clear the memory for the M9045B and M9048A adapters.

FAQ 2012-05-01

Is BER available on the N5182B MXG or N5172B EXG X-Series signal generators?
No, Option UN7, Internal Bit Error Rate Analyzer, is not available at introduction.

FAQ 2012-04-30

How can I program the N5102A DSIM on the N5182B MXG or N5172B EXG X-Series signal generator?
The DSIM is planned to be available late 2012. The DSIM is programmed from the front panel of the MXG, just like the ESG, no external PC needed.

FAQ 2012-04-30

Does Option UNY, enhanced low phase noise, require Option UNX, low phase noise,on the X-Series signal generators?
No, they are independent options with different levels of phase noise performance above 3 GHz.

FAQ 2012-04-30

Does Option UNU, pulse modulation, exist on the X-Series signal generators?
No, Option UNW, narrow pulse, is the only pulse option.

FAQ 2012-04-30

What are the plans to upgrade the N5102A DSIM, if I want it to go to 160 MHz BW on the N5182B MXG or N5172B EXG X-Series signal generators?
DSIM will be able to run up to 200MSa/sec.

FAQ 2012-04-30

Does Option 320 require that I have Option UNU or UNW on the X-Series signal generators?
Yes, Option 320, pulse train generator, requires Option UNW, narrow pulse modulation. Option UNU, pulse modulation, is not an option on the X-Series signal generators.

FAQ 2012-04-30

Can you bypass the internal reference chain with clean rubidium source on the X-Series signal generators?
The 10 MHz path is very clean and works with an external reference. The 1-50 MHz tunable path is noisier, see the data sheets for more details.

FAQ 2012-04-30

Can you change the attenuation on external I and Q individually on the N5182B MXG or N5172B EXG X-Series signal generators?
Yes, improved over the first-generation MXG.

FAQ 2012-04-30

Will we be able to have more than 2 USB power sensors on the X-Series signal generators?
Yes, we are able to connect to 4.

FAQ 2012-04-30

Do the new sources de-crypt waveforms in the same way as the legacy sources? Can we just use pre-existing waveforms?
Yes. First-generation MXG N5182A Signal Studio N76xxB waveforms will play in new sources. Exception will be N7613A Signal Studio for Fixed WiMAX which has the legacy N76xxA structure.

FAQ 2012-04-30

Will the N5171B and N5172B EXG X-Series signal generator have an OCXO option for improved drift rate?
No

FAQ 2012-04-30

Previous 1 2 3 4 5 6 7 8 9 10 ... Next