Technical Support
Test & Measurement
Refine the List
By Topic
- Calibration (166)
- Configuration & Installation (828)
- Display Messages/Error Codes (170)
- Licensing (77)
- Measurement & Instrument Fundamentals (212)
- Measurement Techniques (532)
- Operating System & Software (298)
- Operation & Functionality (1120)
- Other Information (297)
- Parts & Accessories (307)
- Printing & Printers (34)
- Product & Firmware Updates & Upgrades (287)
- Product Theory of Operation (282)
- Programming & Data Transfer (511)
- Service & Maintenance (218)
- Specifications & Accuracy (344)
- Troubleshooting (121)
By Application
By Type of Content
- FAQ (7737)
By Product Category
251-275 of 7737
|
Is the performance of 0.4% EVM for 160 MHz 802.11ac best test result or average performance for N5182B MXG or N5172B EXG X-Series signal generators?
0.4% EVM is characteristic data of a small sample of N5182B MXG signal generators using the PXA and VSA 89601B.
FAQ 2012-12-26 |
|
|
Can running user correction calibration over a narrower range improve calibration?
No, the number of points is always fixed at a 5 MHz interval
FAQ 2012-12-26 |
|
|
How long is the factory channel correction calibration good?
The factory channel correction lasts the life of the source.
FAQ 2012-12-26 |
|
|
How does DC calibration affect channel corrections?
If a DC calibration is run with channel corrections applied, this may or may not degrade performance slightly.
FAQ 2012-12-26 |
|
|
Are there any S1 S2 measurements with power sensors on the X-Series signal generators?
No, however, the “User” channel correction routine in X-Series vector signal generators measures DUT channel response in phase and amplitude with power sensor.
FAQ 2012-12-26 |
|
|
Do User channel corrections cover multiple attenuator steps?
Yes. Bypass step, 0 dB step, and 5 dB step.
FAQ 2012-12-26 |
|
|
What software drivers are available for the 34980A and where can I find them?
IVI-COM Driver and 34980A LabVIEW Driver located on Agilent.com at www.agilent.com/find/drivers...
FAQ 2012-12-20 |
|
|
WireScope™ Pro Software Download
FAQ 2012-12-18 |
|
|
What software drivers are available for the 34970A and where can I find them?
IVI-COM Driver, VXIplug&play Driver, and other drivers located at www.agilent.com/find/drivers
FAQ 2012-12-18 |
|
|
VEE Pro: Where can I find information on Agilent VEE Pro Panel Drivers?
VEE Pro Panel Drivers are available from the Drivers, Firmware, and Software section of the VEE product page...
FAQ 2012-12-18 |
|
|
Where do I get Java to display the 34980A web interface?
The Java Virtual Machine code is needed to run the Agilent 34980A web page features. A free download of the Java Virtual Machine (JVM) can be obtained by going to the following web site.
FAQ 2012-12-17 |
|
|
How do I upgrade my N9342C Handheld Spectrum Analyzer?
Find Information on Hardware Upgrades, Instrument Software, Measurement Applications, etc...
FAQ 2012-12-17 |
|
|
How do I upgrade my N9343C Handheld Spectrum Analyzer?
Find Information on Hardware Upgrades, Instrument Software, Measurement Applications, etc...
FAQ 2012-12-17 |
|
|
How do I upgrade my N9344C Handheld Spectrum Analyzer?
Find Information on Hardware Upgrades, Instrument Software, Measurement Applications, etc…
FAQ 2012-12-17 |
|
|
What is embedded software versus Signal Studio software?
View table with descriptions
FAQ 2012-12-14 |
|
|
Which versions of Mathworks Simulink are compatible with 89600 VSA Software?
Compatible versions are listed here
FAQ 2012-12-14 |
|
|
Online eDM
The latest news in Agilent's measurement technologies.
FAQ 2012-12-13 |
|
|
For waveform 5-pack licenses, what alternatives are available for customers that require additional waveform evaluation time after the initial 30-d...
FAQ 2012-12-13 |
|
|
How do you clear the 34980A multifunction switch/measure mainframe and modules, L44xxA series LXI switch and control instruments memories?
Please refer to the documents for a comprehensive listing of memory installed into these products.
FAQ 2012-12-12 |
|
|
How do I measure Bit Error Rate (BER) to a given confidence level on N490xA/B Serial BERTs?
FAQ 2012-12-12 |
|
|
How long does it take to measure a BER of 1 x 10(-12) at a data rate of 9.953Gb/s? What about at 2.488Gb/s?
It is not possible to predict with certainty when errors will occur. Therefore, you must use a confidence level to know when you have tested error-free for long enough to say that you have a BER of better than 10(-12) performance.
FAQ 2012-12-12 |
|
|
When I use the 30-day trial license of the Signal Studio for WiMAX™, how can I check the number of days remaining on temporary license?
Press the front panel keys: Utility > Instrument Adjustments > Instrument Options > Waveform Licenses
FAQ 2012-12-11 |
|
|
For waveform 5-pack licenses, can the customer download a waveform generated with the 30-day license?
Yes, if a waveform was created using the 30-day trial, it can be downloaded to any MXG/ESG with unused waveform 5-pack license slots.
FAQ 2012-12-11 |
|
|
EPM Series Power Meters Firmware Archive
Download access to older revisions of the EPM Series Power Meters Firmware.
FAQ 2012-12-11 |
|
|
Is there a 30-day trial license for this application?
Only selected Signal Studio software applications have the 30-day free trial license available, while others allow a free evaluation of the software interface only.
FAQ 2012-12-11 |
|
Enroll in myAgilent
Register Your Product
Why Buy Agilent