Technical Support
Parameter & Device Analyzers, Curve Tracer
1-25 of 52
|
How many capacitance measurement units (MFCMUs) can be installed in the B1500A?
Only one MFCMU can be installed in a B1500A mainframe.
FAQ 2012-06-07 |
|
|
[B1542A] Do not use a base line voltage of gate pulse exceeding +/- 3V range
Do not use a base line voltage of gate pulse lower than -3 V or larger than +3 V to avoid a potential risk of damage on the pulse divider used in the gate cabling system.
FAQ 2012-01-11 |
|
|
[B1542A] Dose 81130A supported by the B1542A Ultra Narrow Pulsed IV solution?
No.
FAQ 2011-11-17 |
|
|
[B1542A] What is the maximaum volatge range of gate pulse?
The maximum voltage rage of gate pulse supported by the B1542A Ultra Narrow Pulsed IV solution is
-Pulse top: -4.5 V to + 4.5V,
-Pulse base::-3 V to +3 V,
-Amplitude: 4.5 V or less.
FAQ 2011-11-17 |
|
|
Does Agilent provide the upgrade product for OS of B1500A from XP to Windows 7?
No, it doesn't.
FAQ 2011-10-26 |
|
|
What is required to run EasyEXPERT 4.2 or later?
Click the above link for details.
FAQ 2011-10-26 |
|
|
What is required to run EasyEXPERT 3.2 to 4.11?
The software requirements of EasyEXPERT 3.2 to 4.11 are as follows.
FAQ 2011-10-26 |
|
|
Can I transport my 4155 and 4156 measurement setups over to the B1500A?
Yes.
FAQ 2011-09-08 |
|
|
If I purchase additional modules for my B1500A can I install them myself?
Agilent does not recommend user self-installation of modules.
FAQ 2011-04-12 |
|
|
I need to do a system recovery on my B1500A. How should I back up my data?
You can use the Microsoft Windows Backup utility to perform a data backup.
FAQ 2011-02-15 |
|
|
Where can I find system requirements for Desktop EasyEXPERT?
System requirements for Desktop EasyEXPERT can be found in the B1500A data sheet.
FAQ 2011-02-15 |
|
|
Can I control an Agilent 4284A/E4980A using my B1500A to make CV measurements and display the results in the EasyEXPERT data display window?
Yes.
FAQ 2011-02-15 |
|
|
Can I use Curve Tracer Mode on the B1500A?
Yes. EasyEXPERT 4.0 or later supports Curve Tracer Mode on the B1500A.
FAQ 2011-02-15 |
|
|
Does the B1500A have switching matrix drivers?
Yes.
FAQ 2011-02-14 |
|
|
Can I rearrange the order of the modules in my B1500A?
No.
FAQ 2011-02-14 |
|
|
How do I recover my B1500A in case I have a problem? I did not receive a Windows OS recovery CD with my instrument.
There is no windows recovery CD supplied with the instrument.
FAQ 2011-02-14 |
|
|
Prober Drivers of B1500A
Prober drivers to control semi-automatic prober from the B1500A.
FAQ 2010-10-01 |
|
|
Does the B1500A have any wafer prober drivers?
Yes.
FAQ 2010-10-01 |
|
|
Can I perform routine Microsoft Windows updates on my instrument’s OS via the internet?
The effects of performing a Microsoft Windows update on the B1500A software or firmware cannot be predicted ahead of time.
FAQ 2009-10-20 |
|
|
If I purchase additional modules for my B1500A do I also have to pay to have Agilent install them?
Yes.
FAQ 2009-10-15 |
|
|
Microsoft Windows Security Updates
Download Microsoft Windows security updates
FAQ 2009-05-27 |
|
|
How do I get the latest EasyEXPERT software revisions?
EasyEXPERT software updates and patches can be found on the B1500A product page under “Technical Support.”
FAQ 2009-03-01 |
|
|
Does the B1500A support the measurement append feature?
Yes.
FAQ 2009-03-01 |
|
|
Can I network my B1500A?
The B1500A has a 10BASE-T/100BASE-T LAN port, and it can be networked like any other Microsoft Windows-based PC. However...
FAQ 2009-03-01 |
|
|
Can I use the B1500A medium-frequency capacitance measurement unit (MFCMU) to make device impedance measurements?
Yes.
FAQ 2009-03-01 |
|
Enroll in myAgilent
Register Your Product
Why Buy Agilent