Technical Support
Test & Measurement
Refine the List
By Topic
-
All Topics
- Specifications & Accuracy
By Type of Content
- FAQ (344)
By Product Category
51-75 of 344
|
How is measurement accuracy calculated when the 42841A is used with the 4284A, 4285A or E4980A?
The measurement accuracy is the sum of the measurement instrument accuracy and additional error produced when the instrument is used with the 42841A and bias current test fixture.
FAQ 2010-07-02 |
|
|
How wide range of resistivity can the 4339B measure when used with the 16008B?
The 4339B can measure surface resistivity up to 7 x 1017 Ω and volume resistivity up to 8 x 1018 Ω-cm, but it depends on the electrodes of the 16008B used.
FAQ 2010-07-02 |
|
|
Do the coaxial Short and 50 Ω Load terminations for the 42941A have accuracy specifications?
No, both the coaxial Short and 50 Ω Load standard terminations for the 42941A do not have accuracy specifications.
FAQ 2010-07-02 |
|
|
What operating systems does VEE support?
See the support matrix...
FAQ 2010-06-14 |
|
|
What differentiates a power splitter and power divider and when should one be utilized over the other?
The fundamental difference between power splitters and power dividers (combiners) is the resistor configuration used to separate the power.
FAQ 2010-06-11 |
|
|
What are the differences between the E4446A and the E4447A?
Click here for additional information
FAQ 2010-06-10 |
|
|
What is the main reason that SMT manufacturers would use solder paste inspection for lead-free paste?
The print process for lead free requires fine tuning such as cycle time modifications, reduction in the aperature-to-pad ratios, squeegee speed/pressure changes, etc.
FAQ 2010-05-19 |
|
|
No Title
Instead of the ("Counter value"/"48 x 10^6") as the duration in seconds taken to count, it is...
FAQ 2010-05-10 |
|
|
What is the correct linearity setting for V8486A & W8486A sensor?
The automatic selection must be overridden: select the D type linearity for this sensor.
FAQ 2010-05-10 |
|
|
Is number of bits the only factor to look at if I'm measuring at very low voltage say 5mVpp?
No it is not. Often times, you will have to look at the Gain Error and Offset Error as well as...
FAQ 2010-05-10 |
|
|
How to calculate the accuracy for U1731B/U1732B Inductance Measurements?
The accuracy is calculated using the formula in the datasheet...... The Example......
FAQ 2010-05-05 |
|
|
How to calculate the accuracy for U1731B/U1732B Capacitance Measurements?
The accuracy is calculated using the formula in the datasheet...... The Example......
FAQ 2010-05-03 |
|
|
What is the difference between the 8614xA series and the 8614xB series Optical Spectrum Analyzer?
The 8614xB series has higher wavelength accuracy and faster trace updates than the 8614xA series.
FAQ 2010-04-23 |
|
|
Is the USB connection of U2300A,U2500A and U2600A optically coupled?
No. It is not.
FAQ 2010-03-22 |
|
|
What is the relationship between the “No. of Least Significant Digit” and the accuracy of a handheld meter?
The “No. of Least Significant Digit” affects the accuracy of a handheld meter....
FAQ 2010-02-21 |
|
|
What is the relationship between the “No. of Least Significant Digit” and the accuracy of a handheld multimeter?
The “No. of Least Significant Digit” affects the accuracy of a handheld multimeter....
FAQ 2010-01-07 |
|
|
How does the measurement accuracy of the N8480 series Power Sensors compare to that of the legacy 8480 series sensors?
The N848xA Power Sensors are as accurate if not more accurate than the legacy 848xA sensors they replace….
FAQ 2009-12-15 |
|
|
What does ENOB of 13.3 bit means in the specification sheet?
ENOB = (SINAD-1.76)/6.02
Overall Accuracy = ENOB (Effective Number of Bits)....
FAQ 2009-12-15 |
|
|
When the 4287A displays inaccurate Rdc measurement values, what is required to make more proper Rdc measurements for contact check?
Perform Open/Short/Load calibration and Open/Short compensation.
FAQ 2009-12-09 |
|
|
Does the 4395A have source power calibration function?
No, the 4395A doesn't have the built-in power meter for calibrating the source power at the test port. The source power accuracy is +/- 1.0 dB.
FAQ 2009-12-09 |
|
|
What is the relationship between the "Count" and the accuracy of U3401A or U3402A Digital Multimeter?
One "count" is defined as a unit change (change of 1) in the last digit of the meter display…
FAQ 2009-10-20 |
|
|
What does "Display Counts" means in the U3401A/U3402A Digital Multimeter Datasheet?
Display counts give the largest number the multimeter's display can show….
FAQ 2009-09-29 |
|
|
Does E5818A supports Precision Time Protocol Version 2 (PTPv2)/IEEE 1588 v2?
No, E5818A supports PTPv1/IEEE 1588.
FAQ 2009-09-29 |
|
|
How do I know what is the best sampling rate to use for my measurement?
Typically if you follow Nyquist theory, your sampling rate should be 2x the highest frequency of the incoming signal that you are measuring. However, we recommend that you use 5x...
FAQ 2009-09-29 |
|
|
What is the size and resolution of the Agilent X-Series (PXA/MXA/EXA/CXA) Signal Analyzer display?
Click here for details...
FAQ 2009-09-26 |
|
Enroll in myAgilent
Register Your Product
Why Buy Agilent