|
|
|
Can I use any instrument driver software for the 4284A?
National Instrument’s LabVIEW driver supports the 4284A.
|
2009-03-11
|
FAQ
|
|
|
|
|
Do the 4284A GPIB commands comply with SCPI?
Yes. The GPIB programming language of the 4284A is SCPI.
|
2009-03-11
|
FAQ
|
|
|
|
|
How Can I use the Handler Interface (Opt. 201)?
|
2002-06-27
|
FAQ
|
|
|
|
|
How do I calculate the accuracy of 4284A when the desired stimulus is RMS current rather than RMS voltage?
The Agilent 4284A data sheet provides measurement accuracy as a function of stimulus level in RMS volts.
|
2007-05-09
|
FAQ
|
|
|
|
|
How do I get Instrument Drivers for Agilent Test & Measurement Products?
From the CD shipped with the instrument or from the product technical support web page for the instrument.
|
2009-05-01
|
FAQ
|
|
|
|
|
How would I distinguish between old EEPROM (PN 1818-5719) and new one (PN 5183-4149) when transferring the EEPROMs to new CPU board?
It can be distinguished with the manufacturer part number on the top of the EEPROMs.
|
2008-06-27
|
FAQ
|
|
|
|
|
Is it possible to measure the leakage inductance of a transformer via an LCR meter or impedance analyzer?
Yes, it is possible to measure the leakage inductance of a transformer via an LCR meter or impedance analyzer.
|
2008-01-29
|
FAQ
|
|
|
|
|
Is there a 16060A-like transformer test fixture usable with the 4284A?
No transformer test fixture for the 4284A is available.
|
2009-03-11
|
FAQ
|
|
|
|
|
My Agilent 4284A / 4285A LCR Meter is indicating an "ADC ERR" error message. What are the corrective actions?
The error message is an indication that the LCR meter's A/D converter within the measurement circuit is malfunctioning.
|
2007-05-03
|
FAQ
|
|
|
|
|
On the Agilent 4284A LCR meter, how do I determine which options are installed?
|
2006-10-17
|
FAQ
|
|
|
|
|
Performance Test
|
2003-05-21
|
FAQ
|
|
|
|
|
The instrument often hangs with the error "Trap xxxx" when accessing the correction menu. What do you suggest for avoiding it?
The faulty 4284A might be recovered using a GPIB command without replacing the EEPROM or CPU.
|
2008-06-27
|
FAQ
|
|
|
|
|
What are the precautions when using the Agilent 4284A Impedance Analyzer with the Agilent 42841A and 42842A/B Fixtures?
|
2006-08-01
|
FAQ
|
|
|
|
|
What does the instrument's rear panel look like?
|
2002-06-27
|
FAQ
|
|
|
|
|
What is max. DC output voltage when two 42841A units are used as a 40A system?
|
2002-06-27
|
FAQ
|
|
|
|
|
What is the Agilent 16065A Bias Voltage Test Fixture maximum DC current specification?
The 16065A maximum dc bias current is not specified. However, based upon the 100kΩ input resistance,...
|
2008-07-07
|
FAQ
|
|
|
|
|
What is the memory capacity of the memory card (P/N: 04278-89001)?
|
2002-06-27
|
FAQ
|
|
|
|
|
What is the minimum size SMD (surface mount device) that the Agilent 16095A probe test fixture can measure?
The 16095A standard probe tip diameter is approximately 1.0 mm...
|
2008-01-14
|
FAQ
|
|
|
|
|
What is the output impedance for the various Agilent Impedance Analyzers?
The table below lists the output impedance for the various Agilent Impedance Analyzers.
|
2006-08-15
|
FAQ
|
|
|
|
|
What is the procedure to replace the probe pin(s) on the Agilent 16044A fixture?
Probe pin replacement on the Agilent 16044A is documented in the "Agilent 16044A Test Fixture Operation and Service Manual".
|
2008-01-14
|
FAQ
|
|
|
|
|
What is the recommended procedure for measuring the impedance tangent delta?
|
2005-04-19
|
FAQ
|
|
|
|
|
What resources does Agilent recommend to help facilitate learning proper impedance measurement techniques?
|
2008-01-14
|
FAQ
|
|
|
|
|
When measuring a capacitor via an Agilent LCR meter, what is the best circuit mode, Cs or Cp?
|
2008-01-30
|
FAQ
|
|
|
|
|
When the E4980A/4284A LCR meter displays "ALC unable to regulate" error message, what corrective action should be performed?
|
2009-06-22
|
FAQ
|
|
|
|
|
When utilizing the Agilent 16085B 4-Terminal Pair to 7 mm (APC-7) adapter, is it advisable to use fixture compensation standards or coaxial calibration standards?
|
2008-07-10
|
FAQ
|
|
