|
|
|
Can I use any instrument driver software for the 4285A?
|
2009-01-08
|
FAQ
|
|
|
|
|
Can I use the 16048B with the 4285A for the cable extension?
Yes, the 16048B (Part Number 16048-60030) can be used with the 4285A. But, it is not easy to perform the cable correction using the 100-ohm resistor box (furnished with the 4285A).
|
2009-01-13
|
FAQ
|
|
|
|
|
Can open/short/load correction data be entered in the 4285A from an external PC over GPIB?
|
2009-01-14
|
FAQ
|
|
|
|
|
How can I order the operation notes for the 4285A options 201, 202 and 301?
|
2009-05-26
|
FAQ
|
|
|
|
|
How can I order the upgrade kits for the 4285A?
The available upgrade kits are listed on the 4285A Option Upgrades page, which is linked to Agilent LCR Meters Upgrades homepage.
|
2009-01-14
|
FAQ
|
|
|
|
|
How do I get Instrument Drivers for Agilent Test & Measurement Products?
From the CD shipped with the instrument or from the product technical support web page for the instrument.
|
2009-05-01
|
FAQ
|
|
|
|
|
How often should we perform the verification procedure described in the Performance Tests section of the manual?
Every 12 months.
|
2008-01-11
|
FAQ
|
|
|
|
|
How would I distinguish between old EEPROM (PN 1818-5719) and new one (PN 5183-4149) when transferring the EEPROMs to new CPU board?
It can be distinguished with the manufacturer part number on the top of the EEPROMs.
|
2008-06-27
|
FAQ
|
|
|
|
|
Is it possible to measure the leakage inductance of a transformer via an LCR meter or impedance analyzer?
Yes, it is possible to measure the leakage inductance of a transformer via an LCR meter or impedance analyzer.
|
2008-01-29
|
FAQ
|
|
|
|
|
My Agilent 4284A / 4285A LCR Meter is indicating an "ADC ERR" error message. What are the corrective actions?
The error message is an indication that the LCR meter's A/D converter within the measurement circuit is malfunctioning.
|
2007-05-03
|
FAQ
|
|
|
|
|
What are the key points of the techniques for integrating the 4285A in a scanner system?
To select an appropriate scanner, you need to determine the connection method (three-terminal, four-terminal, shielded four-terminal, etc) suitable for the impedance range of the devices to be measured.
|
2009-01-14
|
FAQ
|
|
|
|
|
What are the precautions when using the Agilent 4284A Impedance Analyzer with the Agilent 42841A and 42842A/B Fixtures?
|
2006-08-01
|
FAQ
|
|
|
|
|
What compensation should I perform when I use the 16048B with the 4285A?
It is recommended to set the Cable Length function of the 4285A to "1 m" and perform open/short/load compensation at the DUT contact terminals of the test fixture connected to the tip of the 16048B.
|
2009-01-13
|
FAQ
|
|
|
|
|
What does the instrument's rear panel look like?
|
2002-06-27
|
FAQ
|
|
|
|
|
What is the Agilent 16065A Bias Voltage Test Fixture maximum DC current specification?
The 16065A maximum dc bias current is not specified. However, based upon the 100kΩ input resistance,...
|
2008-07-07
|
FAQ
|
|
|
|
|
What is the maximum DC bias output current of the 4285A with option 001?
|
2009-01-12
|
FAQ
|
|
|
|
|
What is the output impedance for the various Agilent Impedance Analyzers?
The table below lists the output impedance for the various Agilent Impedance Analyzers.
|
2006-08-15
|
FAQ
|
|
|
|
|
What is the output impedance of the 4285A?
|
2009-01-14
|
FAQ
|
|
|
|
|
What is the recommended procedure for measuring the impedance tangent delta?
|
2005-04-19
|
FAQ
|
|
|
|
|
What resources does Agilent recommend to help facilitate learning proper impedance measurement techniques?
|
2008-01-14
|
FAQ
|
|
|
|
|
When measuring a capacitor via an Agilent LCR meter, what is the best circuit mode, Cs or Cp?
|
2008-01-30
|
FAQ
|
|
|
|
|
When utilizing the Agilent 16085B 4-Terminal Pair to 7 mm (APC-7) adapter, is it advisable to use fixture compensation standards or coaxial calibration standards?
|
2008-07-10
|
FAQ
|
|
|
|
|
Where can I find manuals for discontinued and obsolete Hewlett-Packard and Agilent test equipment?
Most Agilent products have PDF manuals that can be found on product pages. Other vendors also supply old manuals.
|
2009-11-04
|
FAQ
|
|
