Thread: Calibration Wizard

Reply to this Thread Reply to this Thread Search Forum Search Forum Back to Thread List Back to Thread List

Permlink Replies: 5 - Pages: 1 - Last Post: Jul 18, 2012 10:42 AM Last Post By: daras
Dragan.MCL

Posts: 3
Registered: 07/17/12
Calibration Wizard
Posted: Jul 17, 2012 11:32 AM
Click to report abuse...   Click to reply to this thread Reply
Hi,
I have not have any problem to open Cal Wizard, for Swept IMD measurement class, using our test program and PNA-X N5242A.
After we installed a new firmware (A.09.50.13) I am not able to do it anymore.
code:
app11:=app as IApplication11;
app11.LaunchDialog('CalibrationWizard','');

error:
"Method LaunchDialog failed: Could not create the measurement. The application name was not recognized."

Please advise.
Dragan.
daras


Posts: 759
Registered: 12/01/05
Re: Calibration Wizard
Posted: Jul 17, 2012 12:35 PM   in response to: Dragan.MCL in response to: Dragan.MCL
Click to report abuse...   Click to reply to this thread Reply
can you tell us what version you had previously, where this code actually worked? Also is it possible for you to include a state file of your setup right before you execute this code? the IApplication.LaunchDialog() and IApplication.LaunchCalWizard() methods rely on the identity of the active measurement to launch the correct dialog/cal wizard, so it makes a difference what channel/measurement is active.
Dragan.MCL

Posts: 3
Registered: 07/17/12
Re: Calibration Wizard
Posted: Jul 17, 2012 1:26 PM   in response to: Dragan.MCL in response to: Dragan.MCL
Click to report abuse...   Click to reply to this thread Reply
Test program send me no error with this firmware version A.09.22.12.
daras


Posts: 759
Registered: 12/01/05
Re: Calibration Wizard
Posted: Jul 17, 2012 5:16 PM   in response to: Dragan.MCL in response to: Dragan.MCL
Click to report abuse...   Click to reply to this thread Reply
You are correct - I have confirmed that this command worked in A.09.22.12 and it is not working properly in A.09.33.xx and newer versions of firmware. I am going to enter this into our defect tracking system and we will assign an engineer to start working on fixing the problem. However, I need some more information from you in order to determine in which branch of the firmware to fix this issue. Our most current shipping branch on PNA-X's is A.09.50.13, will you be able to upgrade to this version (or newer) or do you prefer to stay on the A.09.33.xx branch? Also how critically is this issue affecting your work? our next scheduled release is towards the end of August; will you be able to wait until then or do you need the fix sooner?
Dragan.MCL

Posts: 3
Registered: 07/17/12
Re: Calibration Wizard
Posted: Jul 18, 2012 10:12 AM   in response to: Dragan.MCL in response to: Dragan.MCL
Click to report abuse...   Click to reply to this thread Reply
We are going to use the last firmware, A.09.50.13 or newer, because of need to test X parameters. We are waiting for you to fix this bug.

Best Regards,
Dragan.
daras


Posts: 759
Registered: 12/01/05
Re: Calibration Wizard
Posted: Jul 18, 2012 10:42 AM   in response to: Dragan.MCL in response to: Dragan.MCL
Click to report abuse...   Click to reply to this thread Reply
I have submitted the defect with highest priority. one of our support engineers will probably contact you directly to get more information and let you know when an update will be available.
Pages: 1
Back to Thread List Back to Thread List

Point your RSS reader here for a feed of the latest messages in all forums